Guest

Tools & Resources

SNMP Object Navigator


CISCO-POP-MGMT-MIB

View compiling dependencies for other MIBS by clearing the page and selecting another MIB.

Compile the MIB

Before you can compile CISCO-POP-MGMT-MIB , you need to compile the MIBs listed below in the order listed.

Download all of these MIBs (Warning: does not include non-Cisco MIBs) or view details about each MIB below.

If you are using Internet Explorer click here.

      MIB Name   Version 1   Version 2   Dependencies
    1. SNMPv2-SMI Download  |  Download  |  View Dependencies
    2. SNMPv2-TC Download  |  Download  |  View Dependencies
    3. SNMPv2-CONF Not Required  |  Download  |  View Dependencies
    4. SNMPv2-MIB Download  |  Download  |  View Dependencies
    5. IANAifType-MIB Download  |  Download  |  View Dependencies
    6. IF-MIB Download  |  Download  |  View Dependencies
    7. PerfHist-TC-MIB Download  |  Download  |  View Dependencies
    8. CISCO-SMI Download  |  Download  |  View Dependencies
    9. DS1-MIB Download  |  Download  |  View Dependencies
    10. RFC1155-SMI   Non-Cisco MIB   |  Non-Cisco MIB   |  -
    11. RFC-1212   Non-Cisco MIB   |  Non-Cisco MIB   |  -
    12. RFC-1215   Non-Cisco MIB   |  Non-Cisco MIB   |  -
    13. SNMPv2-TC-v1   Non-Cisco MIB   |  Non-Cisco MIB   |  -
    14. CISCO-POP-MGMT-MIB Download  |  Download  | 

More Downloads

OID File: CISCO-POP-MGMT-MIB.oid
Capability File: CISCO-POP-MGMT-CAPABILITY

Extra Information

None

MIB Contents

This is the SMI version 2 of the MIB. Click here to see the SMI version 1
        
		
            
                
                    



-- *****************************************************************
-- CISCO-POP-MGMT-MIB.my:  Cisco PoP management MIB file.
--
-- Copyright (c) 1997, 1998, 1999, 2000, 2001, 2005 by cisco Systems, Inc.
-- All rights reserved.
-- *****************************************************************


CISCO-POP-MGMT-MIB DEFINITIONS ::= BEGIN


IMPORTS
        MODULE-IDENTITY,
        NOTIFICATION-TYPE,
        OBJECT-TYPE,
        IpAddress,
        Integer32,
        Gauge32,
        Counter32,
        TimeTicks,
        Unsigned32
                FROM SNMPv2-SMI
        MODULE-COMPLIANCE,
        OBJECT-GROUP,
        NOTIFICATION-GROUP
                FROM SNMPv2-CONF
        DisplayString,
        TimeStamp,
        TruthValue
                FROM SNMPv2-TC
        InterfaceIndexOrZero
                FROM IF-MIB
        dsx1LineStatus,
        dsx1LineIndex
               FROM DS1-MIB
        ciscoExperiment
                FROM CISCO-SMI;

ciscoPopMgmtMIB MODULE-IDENTITY
        LAST-UPDATED    "200512210000Z"
        ORGANIZATION    "Cisco Systems, Inc."
        CONTACT-INFO
                "       Cisco Systems
                        Customer Service

                Postal: 170 W Tasman Drive
                        San Jose, CA  95134
                        USA

                   Tel: +1 800 553-NETS

                E-mail: cs-apm@cisco.com"
        DESCRIPTION                "Cisco Point Of Presence Management MIB to provide DSX1
                 and DSX0 facilities management and call summaries.
"

        REVISION        "200512210000Z"
        DESCRIPTION                "Imported dsx1LineIndex from DS1-MIB instead of 
                 RFC1406-MIB
                 
                 Changed SYNTAX of
                  cpmDS1SlotIndex
                  cpmDS1PortIndex
                  cpmChannelIndex
                  cpmDS1UsageSlotIndex
                  cpmDS1UsagePortIndex
                  cpmActiveCallSummaryIndex
                  cpmCallHistorySummaryIndex

                  cpmActiveModemSlot
                  cpmActiveModemPort
                  cpmActiveEntrySlot
                  cpmActiveEntryPort
                  cpmActiveEntryChannel
                 
                 from Integer32 to Integer32 (0..2147483647)

                 Imported Unsigned32 from SNMPv2-SMI instead of 
                 CISCO-TC.
"

        REVISION        "200212260000Z"
        DESCRIPTION                "Added voice(6) to object cpmCallType.
                 Added Notification Group cpmNotificationGroupRev1
"

        REVISION        "200011290000Z"
        DESCRIPTION                "Added cpmCallVolume with objects:
            cpmCallVolSuccISDNDigital
            cpmCallVolAnalogCallClearedNormally
"


        REVISION        "200003030000Z"
        DESCRIPTION                "Extended cpmDs1DS0UsageTable with objects:
                   cpmDS1TotalAnalogCalls
                   cpmDS1TotalDigitalCalls
                   cpmDS1TotalV110Calls
                   cpmDS1TotalV120Calls
                   cpmDS1TotalCalls
                   cpmDS1TotalTimeInUse
                   cpmDS1CurrentIdle
                   cpmDS1CurrentOutOfService
                   cpmDS1CurrentBusyout
                   cpmDS1InOctets
                   cpmDS1OutOctets
                   cpmDS1InPackets
                   cpmDS1OutPackets

                 Added system level summary objects:
                   cpmISDNCfgActiveDChannels
                   cpmISDNCfgBChannelsTimeInUse
                   cpmISDNCfgBChannelsTimeInUseAnalog
                   cpmISDNCfgBChannelCalls
                   cpmISDNCfgBChannelAnalogCalls
                   cpmTotalISDNSyncPPPCalls 

                 Added DS0StatusTable with objects:
                   cpmDS0OperStatus
                   cpmDS0BusyoutAdminStatus
                   cpmDS0BusyoutAllow
                   cpmDS0BusyoutStatus
                   cpmDS0BusyoutSource
                   cpmDS0BusyoutTime
                   cpmDS0ConfigFunction
                   cpmDS0InterfaceIndex

                 Added busyout notification and
                 notification enable object:
                   cpmDS0BusyoutNotification
                   cpmDS0BusyoutNotifyEnable
                   cpmDS1LoopbackNotifyConfig
                   cpmDS1LoopbackNotifyEnable
                   cpmDS1LoopbackNotification
                
"
    


        REVISION        "9802020000Z"
        DESCRIPTION                "Added objects:
                        cpmISDNCfgBChanInUseForVoice
                        cpmCASCfgBChanInUseForVoice
                 Added enumeration-type:
                        voice
"


        REVISION        "9710210000Z"
        DESCRIPTION                "Added objects:
                        cpmDS1DS0UsageTable
                        cpmActiveDS0sHighWaterMark
                        cpmSW56CfgBChannelsInUse
"


        REVISION        "9705010000Z"
        DESCRIPTION                "Initial version of this MIB module.
"

        ::= { ciscoExperiment 19 }


ciscoPopMgmtMIBObjects  OBJECT IDENTIFIER ::= { ciscoPopMgmtMIB 1 }
 
cpmDS0Usage           OBJECT IDENTIFIER ::= { ciscoPopMgmtMIBObjects 1 }
cpmCallFailure        OBJECT IDENTIFIER ::= { ciscoPopMgmtMIBObjects 2 }
cpmActiveCallSummary  OBJECT IDENTIFIER ::= { ciscoPopMgmtMIBObjects 3 }
cpmCallHistorySummary OBJECT IDENTIFIER ::= { ciscoPopMgmtMIBObjects 4 }
cpmDS0Status          OBJECT IDENTIFIER ::= { ciscoPopMgmtMIBObjects 5 }
cpmDS1LoopbackNotifyConfig  OBJECT IDENTIFIER ::= 
                               { ciscoPopMgmtMIBObjects 6 }
cpmCallVolume               OBJECT IDENTIFIER ::=
                               { ciscoPopMgmtMIBObjects 7 }


-- cpmDS0Usage

cpmDS0UsageTable OBJECT-TYPE
    SYNTAX SEQUENCE OF CpmDS0UsageEntry
    MAX-ACCESS not-accessible
    STATUS current
    DESCRIPTION        "The DS0 usage table is for hardware and software
         objects not used as interfaces, and not covered in
         rfc1213.  These objects include analog calls coming 
         over ISDN, Channelized T1, and Channelized E1.  This
         table is created for every DS1 line in the device.
"
    ::= { cpmDS0Usage 1 }

cpmDS0UsageEntry OBJECT-TYPE
    SYNTAX CpmDS0UsageEntry
    MAX-ACCESS not-accessible
    STATUS current
    DESCRIPTION        "An entry in the DS0 Usage table.
"
    INDEX {cpmDS1SlotIndex, cpmDS1PortIndex, cpmChannelIndex }
    ::= { cpmDS0UsageTable 1 }

CpmDS0UsageEntry ::= SEQUENCE {
    cpmDS1SlotIndex Integer32,
    cpmDS1PortIndex Integer32,
    cpmChannelIndex Integer32,
    cpmConfiguredType INTEGER,
    cpmDS0CallType INTEGER,
    cpmL2Encapsulation INTEGER,
    cpmCallCount Counter32,
    cpmTimeInUse TimeTicks,
    cpmInOctets Counter32,
    cpmOutOctets Counter32,
    cpmInPackets Counter32,
    cpmOutPackets Counter32,
    cpmAssociatedInterface InterfaceIndexOrZero
    }

cpmDS1SlotIndex OBJECT-TYPE
    SYNTAX  Integer32 (0..2147483647)
    MAX-ACCESS  not-accessible
    STATUS current
    DESCRIPTION        "The slot index indicates the slot number on the 
         device where the DS1 card resides.
"
    ::= { cpmDS0UsageEntry 1 }

cpmDS1PortIndex OBJECT-TYPE
    SYNTAX  Integer32 (0..2147483647)
    MAX-ACCESS  not-accessible
    STATUS current
    DESCRIPTION        "The port index indicates the port number of a
         specific DS1 on the DS1 card in the slot
"
    ::= { cpmDS0UsageEntry 2 }

cpmChannelIndex OBJECT-TYPE
    SYNTAX  Integer32 (0..2147483647)
    MAX-ACCESS  not-accessible
    STATUS current
    DESCRIPTION        "The channel index that distinguishes the DS0 timeslot 
         of the DS1 port.  The range of the channel index is based 
         on the number of T1/E1 channels: 1-24(T1) and 1-31(E1).
"
    ::= { cpmDS0UsageEntry 3 }

cpmConfiguredType OBJECT-TYPE
    SYNTAX  INTEGER {
           unknown(1),
           isdn(2),
           ct1(3),
           ce1(4)
           }
    MAX-ACCESS  read-only
    STATUS current
    DESCRIPTION        "The configured technology for the channel: ISDN(2), 
         Channelized T1 (3) or Channelized E1 (4).
"
    ::= { cpmDS0UsageEntry 4 }

cpmDS0CallType OBJECT-TYPE
    SYNTAX  INTEGER {
       idle(1),
       unknown(2),
       analog(3),
       digital(4),
       v110(5),
       v120(6),
       voice(7)
       }
    MAX-ACCESS  read-only
    STATUS current
    DESCRIPTION        "The type of the current call carried by this DS0.
            idle     - This DS0 is currently idle.
            unknown  - The data type of the call currently
                       occupying this DS0 is not one of the
                       types listed here.
            analog   - The data type of the call currently
                       occupying this DS0 is analog, i.e. a
                       modem call.
            digital  - The data type of the call currently
                       occupying this DS0 is digital.
            v110     - The call currently occupying this 
                       DS0 is a V110 call.
            v120     - The call currently occupying this
                       DS0 is a V120 call.
            voice    - The call currently occupying this
                       DS0 is a voice call.
"
    ::= { cpmDS0UsageEntry 5 }

cpmL2Encapsulation OBJECT-TYPE
    SYNTAX  INTEGER {
       idle(1),
       unknown(2),
       ppp(3),
       slip(4),
       arap(5),
       hdlc(6),
       exec(7),
       voice(8)
       }
    MAX-ACCESS  read-only
    STATUS current
    DESCRIPTION        "The data link encapsulation of the call currently
         occuppying this DS0:
            idle    - This DS0 is currently idle.
            unknown - The encapsulation of the currently
                      active call on this DS0 is not one
                      of the options following.
            PPP     - 
            slip    - 
            arap    -
            hdlc    -
            exec    -
            voice   - voice encapsulation; IANA type voiceEncap(103)
"
    ::= { cpmDS0UsageEntry 6 }

cpmCallCount OBJECT-TYPE
    SYNTAX Counter32
    MAX-ACCESS  read-only
    STATUS current
    DESCRIPTION        "The number of calls that have occupied this DS0.
"
    ::= { cpmDS0UsageEntry 7 }

cpmTimeInUse OBJECT-TYPE
    SYNTAX TimeTicks
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The amount of time that this DS0 has been in use.
         This is computed by summing up the call durations 
         of all past calls that have occupied this DS0.
"
    ::= { cpmDS0UsageEntry 8 }

cpmInOctets OBJECT-TYPE
    SYNTAX  Counter32
    MAX-ACCESS  read-only
    STATUS current
    DESCRIPTION         "The total number of octets received on this DS0 for
          data calls (cpmDS0CallType has the value  'analog(3)'
          or 'digital(4)' or 'v110(5)' or 'v120(6)'). All the
          received 'raw' octets are counted, including any
          protocol headers which may or may not be present,
          depending on the service type of data call.
"
    ::= { cpmDS0UsageEntry 9 }

cpmOutOctets OBJECT-TYPE
    SYNTAX  Counter32
    MAX-ACCESS  read-only
    STATUS current
    DESCRIPTION         "The total number of octets transmitted on this DS0 for
          data calls (cpmDS0CallType has the value  'analog(3)'
          or 'digital(4)' or 'v110(5)' or 'v120(6)'). All the
          transmitted 'raw' octets are counted, including any
          protocol headers which may or may not be present,
          depending on the service type of data call.
"
    ::= { cpmDS0UsageEntry 10 }

cpmInPackets OBJECT-TYPE
    SYNTAX  Counter32
    MAX-ACCESS  read-only
    STATUS current
    DESCRIPTION        "The total number of packets received on this DS0 for
         data calls (cpmDS0CallTyp has the value  'analog(3)'
         or 'digital(4)' or 'v110(5)' or 'v120(6)').
"
    ::= { cpmDS0UsageEntry 11 }

cpmOutPackets OBJECT-TYPE
    SYNTAX  Counter32
    MAX-ACCESS  read-only
    STATUS current
    DESCRIPTION        "The total number of packets transmitted on this DS0 for
         data calls (cpmDS0CallTyp has the value  'analog(3)'
         or 'digital(4)' or 'v110(5)' or 'v120(6)').
"
    ::= { cpmDS0UsageEntry 12 }

cpmAssociatedInterface OBJECT-TYPE
    SYNTAX  InterfaceIndexOrZero
    MAX-ACCESS  read-only
    STATUS current
    DESCRIPTION        "This is the value of ifIndex when the specific channel
         has an active call with a corresponding interface in the
         ifTable.  For example, a digital ISDN call has a value
         pointing to the B-Channel entry in the ifTable.  A 
         modem call over ISDN or CT1/CE1 has a value pointing
         to the async interface of the modem assigned to this 
         call.  If the channel is idle, this value is 0.
"
    ::= { cpmDS0UsageEntry 13 }

-- End of cpmDS0UsageTable


cpmISDNCfgBChanInUseForAnalog OBJECT-TYPE
    SYNTAX Gauge32
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The number of configured ISDN B-Channels that are
         currently occupied by analog calls.
"
    ::= { cpmDS0Usage 2 }

cpmISDNCfgBChannelsInUse OBJECT-TYPE
    SYNTAX Gauge32
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The number of configured ISDN B-Channels that are
         currently occupied by both Digital and Analog calls.
"
    ::= { cpmDS0Usage 3 }

cpmActiveDS0s OBJECT-TYPE
    SYNTAX Gauge32
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The number of DS0s that are currently in use.
"
    ::= { cpmDS0Usage 4 }

cpmPPPCalls OBJECT-TYPE
    SYNTAX Gauge32
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The current number of active PPP calls received 
         by the managed device
"
    ::= { cpmDS0Usage 5 }

cpmV120Calls OBJECT-TYPE
    SYNTAX Gauge32
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The current number of active V.120 calls received 
         by the managed device
"
    ::= { cpmDS0Usage 6 }

cpmV110Calls OBJECT-TYPE
    SYNTAX Gauge32
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The current number of active V.110 calls received 
         by the managed device
"
    ::= { cpmDS0Usage 7 }

cpmActiveDS0sHighWaterMark OBJECT-TYPE
    SYNTAX Counter32
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The high water mark for number of DS0s that are active
         simultaneously
"
    ::= { cpmDS0Usage 8 }


--
-- DS1 Level Statistics Aggregation
--

cpmDS1DS0UsageTable OBJECT-TYPE
    SYNTAX SEQUENCE OF CpmDS1DS0UsageEntry
    MAX-ACCESS not-accessible
    STATUS current
    DESCRIPTION        "The DS1-DS0-usage table is for hardware and software
         objects not used as interfaces, and not covered in
         rfc1213.  These objects provide information on timeslots
         usage for a particular DS1.
"
    ::= { cpmDS0Usage 9 }
 
cpmDS1DS0UsageEntry OBJECT-TYPE
    SYNTAX CpmDS1DS0UsageEntry
    MAX-ACCESS not-accessible
    STATUS current
    DESCRIPTION        "An entry in the DS0 Usage table.
"
    INDEX {cpmDS1UsageSlotIndex, cpmDS1UsagePortIndex }
    ::= { cpmDS1DS0UsageTable 1 }
 
CpmDS1DS0UsageEntry ::= SEQUENCE {
    cpmDS1UsageSlotIndex          Integer32,
    cpmDS1UsagePortIndex          Integer32,
    cpmDS1ActiveDS0s              Gauge32,
    cpmDS1ActiveDS0sHighWaterMark Counter32,
    cpmDS1TotalAnalogCalls        Counter32,
    cpmDS1TotalDigitalCalls       Counter32,
    cpmDS1TotalV110Calls          Counter32,
    cpmDS1TotalV120Calls          Counter32,
    cpmDS1TotalCalls              Counter32,
    cpmDS1TotalTimeInUse          Unsigned32,
    cpmDS1CurrentIdle             Gauge32,
    cpmDS1CurrentOutOfService     Gauge32,
    cpmDS1CurrentBusyout          Gauge32,
    cpmDS1InOctets                Counter32,
    cpmDS1OutOctets               Counter32,
    cpmDS1InPackets               Counter32,
    cpmDS1OutPackets              Counter32
    }
 
cpmDS1UsageSlotIndex OBJECT-TYPE
    SYNTAX  Integer32 (0..2147483647)
    MAX-ACCESS  not-accessible
    STATUS current
    DESCRIPTION        "The slot index indicates the slot number on the
         device where the DS1 card resides. The slot index of 
         the first slot is starting from 0 and increment by 1 for
         the next slot in the device.
"
    ::= { cpmDS1DS0UsageEntry 1 }
 
cpmDS1UsagePortIndex OBJECT-TYPE
    SYNTAX  Integer32 (0..2147483647)
    MAX-ACCESS  not-accessible
    STATUS current
    DESCRIPTION        "The port index indicates the port number of a
         specific DS1 on the DS1 card in the slot. The port index
         of the first port is starting from 0 and increment by 1
         for the next port on the DS1 card.
"
    ::= { cpmDS1DS0UsageEntry 2 }
 
cpmDS1ActiveDS0s OBJECT-TYPE
    SYNTAX Gauge32
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The number of DS0s that are currently in use for a
         particular DS1.
"
    ::= { cpmDS1DS0UsageEntry 3 }
 
cpmDS1ActiveDS0sHighWaterMark OBJECT-TYPE
    SYNTAX Counter32
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The highest number of simultaneously actived DS0s on a
         specified DS1.
"
    ::= { cpmDS1DS0UsageEntry 4 }


 
cpmDS1TotalAnalogCalls OBJECT-TYPE
    SYNTAX Counter32
    UNITS  "calls"
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The accumulated number of analog data calls
         (cpmDS0CallType has the value 'analog(3)') on all
         ds0s within this DS1 since system startup.
         The object includes active and terminated calls.
"
    ::= { cpmDS1DS0UsageEntry 5 }
 
cpmDS1TotalDigitalCalls OBJECT-TYPE
    SYNTAX Counter32
    UNITS  "calls"
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The accumulated number of digital data calls
         (cpmDS0CallType has the value 'digital(4)') on all
         ds0s within this DS1 since system startup.
         The object includes active and terminated calls.
"
    ::= { cpmDS1DS0UsageEntry 6 }
 
cpmDS1TotalV110Calls OBJECT-TYPE
    SYNTAX Counter32
    UNITS  "calls"
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The accumulated number of v.110 data calls
         (cpmDS0CallType has the value 'v110(5)') on all
         ds0s within this DS1 since system startup.
         The object includes active and terminated calls.
"
    ::= { cpmDS1DS0UsageEntry 7 }
 
cpmDS1TotalV120Calls OBJECT-TYPE
    SYNTAX Counter32
    UNITS  "calls"
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The accumulated number of v.120 data calls
         (cpmDS0CallType has the value 'v120(6)') on all
         ds0s within this DS1 since system startup.
         The object includes active and terminated calls.
"
    ::= { cpmDS1DS0UsageEntry 8 }
 
cpmDS1TotalCalls OBJECT-TYPE
    SYNTAX Counter32
    UNITS  "calls"
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The total number of calls on all the DS0s within
         this DS1 since last system re-initialization. The
         object includes active and terminated calls.

         This only includes DS0s configured as bearer channels,
         not those configured for signaling, such as PRI D-channel.
"
    ::= { cpmDS1DS0UsageEntry 9 }
 
cpmDS1TotalTimeInUse OBJECT-TYPE
    SYNTAX Unsigned32
    UNITS "seconds"
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The total call duration on all the DS0s within
         this DS1 since last system re-initialization.

         This only includes DS0s configured as bearer channels,
         not those configured for signaling, such as PRI D-channel.
"
    ::= { cpmDS1DS0UsageEntry 10 }

cpmDS1CurrentIdle OBJECT-TYPE
    SYNTAX Gauge32
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The total number of DS0s currently in idle state within
         this DS1.

         This only includes DS0s configured as bearer and CAS channels,
         not those configured for signaling, such as PRI D-channel.

         See cpmDS0OperStatus in the cpmDS0StatusTable for individual
         DS0s.
"
    ::= { cpmDS1DS0UsageEntry 11 }
 
cpmDS1CurrentOutOfService OBJECT-TYPE
    SYNTAX Gauge32
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The total number of DS0s in this DS1 currently placed
         out of service.

         This only includes DS0s configured as bearer and CAS channels,
         not those configured for signaling, such as PRI D-channel.

         See cpmDS0OperStatus in the cpmDS0StatusTable for individual
         DS0s.
"
    ::= { cpmDS1DS0UsageEntry 12 }
 
cpmDS1CurrentBusyout OBJECT-TYPE
    SYNTAX Gauge32
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The total number of DS0s in this DS1 which currently have
         been requested to be busied out, but are not yet out of
         service.

         When an active call on a busied out DS0 terminates,
         the DS0 will be out of service, this object will be
         decremented and cpmDS1TotalOutOfService will be
         incremented.

         This only includes DS0s configured as bearer channels,
         not those configured for signaling, such as PRI D-channel.

         See cpmDS0AdminStatus in the cpmDS0StatusTable for individual
         DS0s.
"
    ::= { cpmDS1DS0UsageEntry 13 }

cpmDS1InOctets OBJECT-TYPE
    SYNTAX  Counter32
    UNITS   "octets"
    MAX-ACCESS  read-only
    STATUS current
    DESCRIPTION        "The total number of octets received over all the
         DS0 bearer channels within this DS1 since last system
         re-initialization.

         This value is a sum of all the cpmInOctets objects in
         the cpmDS0UsageTable for this DS1.
"
    ::= { cpmDS1DS0UsageEntry 14 }

cpmDS1OutOctets OBJECT-TYPE
    SYNTAX  Counter32
    UNITS   "octets"
    MAX-ACCESS  read-only
    STATUS current
    DESCRIPTION        "The total number of octets transmitted over all the
         DS0 bearer channels within this DS1 since last system
         re-initialization.

         This value is a sum of all the cpmOutOctets objects in
         the cpmDS0UsageTable for this DS1.
"
    ::= { cpmDS1DS0UsageEntry 15 }

cpmDS1InPackets OBJECT-TYPE
    SYNTAX  Counter32
    UNITS   "packets"
    MAX-ACCESS  read-only
    STATUS current
    DESCRIPTION        "The total number of data packets received over all the
         DS0 bearer channels within this DS1 since last system
         re-initialization.

         This value is a sum of all the cpmInPackets objects in
         the cpmDS0UsageTable for this DS1. It consists of PPP
         or PCM voice data packets.
"
    ::= { cpmDS1DS0UsageEntry 16 }

cpmDS1OutPackets OBJECT-TYPE
    SYNTAX  Counter32
    UNITS   "packets"
    MAX-ACCESS  read-only
    STATUS current
    DESCRIPTION        "The total number of data packets transmitted over all the
         DS0 bearer channels within this DS1 since last system
         re-initialization.

         This value is a sum of all the cpmOutPackets objects in
         the cpmDS0UsageTable for this DS1. It consists of PPP
         or PCM voice data packets.
"
    ::= { cpmDS1DS0UsageEntry 17 }



-- End of cpmDS1DS0UsageTable


--
-- Additional System Level Statistics
--

cpmSW56CfgBChannelsInUse OBJECT-TYPE
    SYNTAX Gauge32
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The number of configured SW56 B-Channels that are
         currently occupied by Digital calls.
"
    ::= { cpmDS0Usage 10 }

cpmISDNCfgBChanInUseForVoice OBJECT-TYPE
    SYNTAX Gauge32
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The number of configured ISDN B-Channels that are
         currently occupied by Voice calls.
"
    ::= { cpmDS0Usage 11 }

cpmCASCfgBChanInUseForVoice OBJECT-TYPE
    SYNTAX Gauge32
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The number of configured CAS Channels that are
         currently occupied by Voice calls.
"
    ::= { cpmDS0Usage 12 }



cpmISDNCfgActiveDChannels OBJECT-TYPE
    SYNTAX Gauge32
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The number of ISDN signaling channels which are active.
"
    ::= { cpmDS0Usage 13 }

cpmISDNCfgBChannelsTimeInUse OBJECT-TYPE
    SYNTAX Counter32
    UNITS "seconds"
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The total call duration on all the ISDN B-channels
         since last system re-initialization.
"
    ::= { cpmDS0Usage 14 }

cpmISDNCfgBChannelsTimeInUseAnlg OBJECT-TYPE
    SYNTAX Counter32
    UNITS "seconds"
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The total analog call duration on all the ISDN B-channels
         since last system re-initialization.

         Analog call type is identified in cpmDS0CallType.
"
    ::= { cpmDS0Usage 15 }

cpmISDNCfgBChannelCalls OBJECT-TYPE
    SYNTAX Counter32
    UNITS  "calls"
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The total number of calls on all the ISDN B-channels
         since last system re-initialization.
"
    ::= { cpmDS0Usage 16 }

cpmISDNCfgBChannelAnalogCalls OBJECT-TYPE
    SYNTAX Counter32
    UNITS  "calls"
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The total number of analog calls on all the ISDN B-channels
         since last system re-initialization.

         Analog call type is identified in cpmDS0CallType.
"
    ::= { cpmDS0Usage 17 }

cpmTotalISDNSyncPPPCalls OBJECT-TYPE
    SYNTAX Counter32
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The total number of ISDN-sync PPP calls received 
         by the managed device since last system re-initialization.
"
    ::= { cpmDS0Usage 18 }



--
-- DS0 Status Group
--

-- Notification Configuration

cpmDS0BusyoutNotifyEnable OBJECT-TYPE
        SYNTAX      TruthValue
        MAX-ACCESS  read-write
        STATUS      current
        DESCRIPTION            "This variable controls generation of
             cpmDS0BusyoutNotification.

             When this variable is 'true(1)', generation of
             cpmDS0BusyoutNotification is enabled.  When this
             variable is 'false(2)', generation of
             cpmDS0BusyoutNotification is disabled.

             The default value is 'false(2)'.
            
"
        ::= { cpmDS0Status 1 }




cpmDS0StatusTable OBJECT-TYPE
    SYNTAX SEQUENCE OF CpmDS0StatusEntry
    MAX-ACCESS not-accessible
    STATUS current
    DESCRIPTION        "The DS0 Status Table provides additional DS0 level
         information and configuration.

         This table is an extension of the cpmDS0UsageTable.
        
"
    ::= { cpmDS0Status 2 }


cpmDS0StatusEntry OBJECT-TYPE
    SYNTAX CpmDS0StatusEntry
    MAX-ACCESS not-accessible
    STATUS current
    DESCRIPTION        "Status for an individual DS0.
         This entry AUGMENTS the cpmDS0UsageEntry.
         An entry exists for each configured DS0 in the system.
        
"
    AUGMENTS { cpmDS0UsageEntry }
    ::= { cpmDS0StatusTable 1 }


CpmDS0StatusEntry ::= SEQUENCE {
    cpmDS0OperStatus          INTEGER,
    cpmDS0BusyoutAdminStatus  INTEGER,
    cpmDS0BusyoutAllow        TruthValue,
    cpmDS0BusyoutStatus       INTEGER,
    cpmDS0BusyoutSource       INTEGER,
    cpmDS0BusyoutTime         TimeStamp,
    cpmDS0ConfigFunction      INTEGER,
    cpmDS0InterfaceIndex      InterfaceIndexOrZero
    }



 
cpmDS0OperStatus     OBJECT-TYPE
    SYNTAX INTEGER {
       unknown(1),
       down(2),
       idle(3),
       setup(4),
       connected(5),
       test(6)
       }
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The operational state of the DSO.
         This object provides more detailed information than
         the IF-MIB ifOperStatus.
            unknown   - The DSO is in an unknown state
            down      - The DS0 is out of service
            idle      - This DS0 is currently idle
            setup     - A new connection is in the process
                        of being established
            connected - A active connection exists
            test      - The DSO is undergoing internal testing

        
"
    ::= { cpmDS0StatusEntry 1 }


 
cpmDS0BusyoutAdminStatus     OBJECT-TYPE
    SYNTAX INTEGER {
       noBusyout(1),
       busyout(2),
       busyoutImmediate(3)
       }
    MAX-ACCESS read-write
    STATUS current
    DESCRIPTION        "The administratively requested busyout state of the DSO.
         This object represents the desired busyout state of the DS0,
         which may or may not be reflected in the operation state,
         cpmDS0OperStatus.

         This object may be set via SNMP or the system console.

            noBusyout - No administrative busyout has been requested
            busyout   - The DS0 will be shutdown when it next
                        transitions to idle(2) cpmDS0OperStatus
            busyoutImmediate  -
                        Immediately transition the DS0 to down(2),
                        terminating any current activity

         The effect of setting this object to busyout or
         busyoutImmediate is constrained by the value of
         cpmDS0BusyoutAllowed. If cpmDS0BusyoutAllowed has a value
         of false, attempting to set this object to busyout or
         busyoutImmediate will fail.


         This object provides more busyout information not available
         from the IF-MIB ifAdminStatus.

         This object reflects busyout requests configured on the
         local system as defined for the object cpmDS0BusyoutSource.
        
"
    ::= { cpmDS0StatusEntry 2 }



cpmDS0BusyoutAllow   OBJECT-TYPE
    SYNTAX TruthValue
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The object indicates if busyout requests for this DSO
         will be allowed.

            true      - Setting cpmDS0BusyoutAdminStatus to busyout(2)
                        or busyoutImmediate(3) will be accepted
            false     - Busyout requests for this DS0 are not
                        allowed

         The default value is true(1).

         If cpmDS0BusyoutAllowed has a value of false(2), attempting
         to set cpmDS0BusyoutAdminStatus to busyout or
         busyoutImmediate will fail.

         This object only constrains setting the value of
         cpmDS0BusyoutAdminStatus when cpmDS0BusyoutAdminStatus is set
         via SNMP.
        
"
    ::= { cpmDS0StatusEntry 3 }


cpmDS0BusyoutStatus     OBJECT-TYPE
    SYNTAX INTEGER {
       noBusyout(1),
       busyoutPending(2),
       busiedOut(3)
       }
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The busyout status of the DSO. 

            noBusyout      - The DS0 is not busied out nor has a
                             busyout pending.
            busyoutPending - The DS0 has a busyout request pending. It
                             will shutdown when it next transitions
                             to idle(2) cpmDS0OperStatus.
            busiedOut      - The DS0 is out of service due to a busyout
                             request.

         This object is needed to reflect busyouts initiated other than
         administrativly, as described in cpmDS0BusyoutSource.
        
"
    ::= { cpmDS0StatusEntry 4 }


cpmDS0BusyoutSource     OBJECT-TYPE
    SYNTAX INTEGER {
       none(1),
       local(2),
       internal(3),
       remote(4)
       }
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The source of the busyout request either pending or
         active for the DSO.

            none     - The DS0 is not busied out nor has a busyout
                       request pending
            local    - The DS0 is busied out or has a pending request
                       due to an adminstrative command issued locally.
            internal - The DS0 is busied out or has a pending request
                       due to internal system processing.
            remote   - The DS0 is busied out or has a pending request
                       due to a request from the peer switch.
        
"
    ::= { cpmDS0StatusEntry 5 }


cpmDS0BusyoutTime     OBJECT-TYPE
        SYNTAX TimeStamp
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION            "Value of sysUpTime when the most recent busyout request
             was issued for this DS0. The value is zero indicates no
             busyout request has been issued.
            
"
        ::= { cpmDS0StatusEntry 6 }


cpmDS0ConfigFunction   OBJECT-TYPE
    SYNTAX INTEGER {
           unknown(1),
           t1CcsSignallingChan(2),
           t1CcsBearerChan(3),
           e1CcsSignallingChan(4),
           e1CcsBearerChan(5),
           t1CasChan(6),
           e1CasChan(7)
       }
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The object indicates the function this DSO is configured
         to provide.

         This object provides more detail than cpmConfiguredType.

            unknown          - Unknown configuration
            t1SignallingChan - DS0 is configured as a T1 common channel
                               signalling (CCS) such as ISDN PRI
                               D-channel
            t1CcsBearerChan  - DS0 is configured as a T1 common channel
                               signalling (CCS) bearer channel
            e1SignallingChan - DS0 is configured as a E1 common channel
                               signalling (CCS) such as ISDN PRI
                               D-channel
            e1CcsBearerChan  - DS0 is configured as a E1 common channel
                               signalling (CCS) bearer channel
            t1CasChan        - DS0 is configured as a T1 channel
                               associated signalling channel
            e1CasChan        - DS0 is configured as a E1 channel
                               associated signalling channel

        
"
    ::= { cpmDS0StatusEntry 7 }


cpmDS0InterfaceIndex OBJECT-TYPE
    SYNTAX  InterfaceIndexOrZero
    MAX-ACCESS  read-only
    STATUS current
    DESCRIPTION        "This is the value of ifIndex in the ifTable for this DS0.
"
    ::= { cpmDS0StatusEntry 8 }




-- cpmCallFailure
--
-- The objects in this section are optimizations so we don't have to
-- retrieve and count tables.  We have examined existing call
-- termination conditions from the CISCO-CALL-HISTORY-MIB, and they
-- do not address the both ISDN and Modem terminations. 

cpmISDNCallsRejected OBJECT-TYPE
    SYNTAX Counter32
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The number of rejected ISDN calls in this managed
         device.
" 
    ::= { cpmCallFailure 1 }

cpmModemCallsRejected OBJECT-TYPE
    SYNTAX Counter32
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The number of rejected modem calls in this managed
         device.
"
    ::= { cpmCallFailure 2 }

cpmISDNCallsClearedAbnormally OBJECT-TYPE
    SYNTAX Counter32
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The number of connected ISDN calls that have been
         abnormally cleared, that is, they were cleared by some
         event other than the following:
         a - The transmission of a normal disconnect message by the 
             local end.
         b - The reception of a normal disconnect message from the 
             remote end.
"
    ::= { cpmCallFailure 3 }

cpmModemCallsClearedAbnormally OBJECT-TYPE
    SYNTAX Counter32
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The number of connected modem calls that have been abnormally
         cleared, that is, they were not cleared with the proper modem
         protocol handshakes.
"
    ::= { cpmCallFailure 4 }

cpmISDNNoResource OBJECT-TYPE
    SYNTAX Counter32 
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The number of ISDN calls that have been rejected because
         there is no B-Channel available to handle the call.
"        
    ::= { cpmCallFailure 5 }

cpmModemNoResource OBJECT-TYPE
    SYNTAX Counter32 
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The number of modem calls that have been rejected because
         there is no modem available to handle the call.
"        
    ::= { cpmCallFailure 6 }


-- cpmCallVolume
--
-- The objects in this section are optimizations so we don't have 
-- to retrieve and count tables.

cpmCallVolSuccISDNDigital OBJECT-TYPE
      SYNTAX Counter32
      MAX-ACCESS read-only
      STATUS current
      DESCRIPTION          "The number of incoming and outgoing successful ISDN 
           digital data calls (cpmDS0CallType has the value 
           'digital(4)'), since system startup.  A successful call is 
           a terminated call that has a disconnect cause of 'normal 
           call clearing(16)'.
"
      ::= { cpmCallVolume 1 }
  
  
cpmCallVolAnalogCallClearedNormally OBJECT-TYPE
      SYNTAX Counter32
      MAX-ACCESS read-only
      STATUS current
      DESCRIPTION          "The number of incoming and outgoing successful
           analog data calls which use modem resource (cpmDS0CallType 
           has the value 'analog(3)'), since system startup. A 
           successful call is a terminated call who is cleared by the
           proper modem protocol handshake.
"
      ::= { cpmCallVolume 2 }


-- cpmActiveCallSummary

cpmActiveCallSummaryTable OBJECT-TYPE
    SYNTAX SEQUENCE OF CpmActiveCallSummaryEntry
    MAX-ACCESS not-accessible
    STATUS current
    DESCRIPTION        "The active call summary table is needed to track 
         currently active calls.  This table is needed 
         because modem calls are not in CALL-HISTORY-MIB,
         and the DIAL-CONTROL_MIB is not yet available.
" 
    ::= { cpmActiveCallSummary 1 }

cpmActiveCallSummaryEntry OBJECT-TYPE
    SYNTAX CpmActiveCallSummaryEntry
    MAX-ACCESS not-accessible
    STATUS current
    DESCRIPTION        "An entry in the Call Summary table.
"
    INDEX {cpmActiveCallStartTimeIndex, cpmActiveCallSummaryIndex }
    ::= { cpmActiveCallSummaryTable 1 }

CpmActiveCallSummaryEntry ::= SEQUENCE {
    cpmActiveCallStartTimeIndex TimeStamp,
    cpmActiveCallSummaryIndex Integer32,
    cpmActiveUserID  DisplayString,
    cpmActiveUserIpAddr IpAddress,
    cpmActiveCallType INTEGER,
    cpmActiveModemSlot Integer32,
    cpmActiveModemPort Integer32,
    cpmActiveCallDuration TimeTicks,
    cpmActiveEntrySlot Integer32,
    cpmActiveEntryPort Integer32,
    cpmActiveEntryChannel Integer32,
    cpmActiveRemotePhoneNumber DisplayString,
    cpmActiveLocalPhoneNumber DisplayString,
    cpmActiveTTYNumber Integer32
    }

cpmActiveCallStartTimeIndex OBJECT-TYPE
    SYNTAX TimeStamp
    MAX-ACCESS not-accessible
    STATUS current
    DESCRIPTION        "The start time of the current call.
"
    ::= { cpmActiveCallSummaryEntry 1 }

cpmActiveCallSummaryIndex OBJECT-TYPE
    SYNTAX Integer32 (0..2147483647)
    MAX-ACCESS not-accessible
    STATUS current
    DESCRIPTION        "Arbitrary small integer to distinguish calls that occured
         at the same time tick.
"
    ::= { cpmActiveCallSummaryEntry 2 }

cpmActiveUserID OBJECT-TYPE
    SYNTAX DisplayString(SIZE(0..255))
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The User login ID or zero length string if unavailable.
"
    ::= { cpmActiveCallSummaryEntry 3 }

cpmActiveUserIpAddr OBJECT-TYPE
    SYNTAX  IpAddress
    MAX-ACCESS  read-only
    STATUS current
    DESCRIPTION        "The IP address of the call or 0.0.0.0 if unavailable.
         This object comes directly from IOS.
"
    ::= { cpmActiveCallSummaryEntry 4 }

cpmActiveCallType OBJECT-TYPE
    SYNTAX INTEGER {
       unknown(1),
       analog(2),
       digital(3),
       v110(4),
       v120(5),
       voice(6)
       }
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The call type:
            unknown  - None of the following 
            analog   - Modem call
            digital  - Digital call
            v110     - V110 Call
            v120     - V120 Call
            voice    - Voice Call
"
    ::= { cpmActiveCallSummaryEntry 5 }

cpmActiveModemSlot OBJECT-TYPE
    SYNTAX     Integer32 (0..2147483647)
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION        "Identification of modem resource allocated to call.
         This is the value of cmSlotIndex from CISCO-MODEM-MGMT-MIB.
         This value along with cpmActiveModemPort uniquely identifies 
         a modem.  Value is -1 if call does not utilize a modem.
"
    ::= { cpmActiveCallSummaryEntry 6 }
 
cpmActiveModemPort OBJECT-TYPE
    SYNTAX     Integer32 (0..2147483647)
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION        "Identification of modem resource allocated to call.
         This is the value of cmPortIndex from CISCO-MODEM-MGMT-MIB.
         This value along with cpmActiveModemSlot uniquely identifies 
         a modem.  Value is -1 if call does not utilize a modem.
"
    ::= { cpmActiveCallSummaryEntry 7 }

cpmActiveCallDuration OBJECT-TYPE
    SYNTAX TimeTicks
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The duration of the current call.
"
    ::= { cpmActiveCallSummaryEntry 8 }

cpmActiveEntrySlot OBJECT-TYPE
    SYNTAX  Integer32 (0..2147483647)
    MAX-ACCESS  read-only
    STATUS current
    DESCRIPTION        "The logical slot in which the DS1 line that the user 
         connected on resides.
"
    ::= { cpmActiveCallSummaryEntry 9 }

cpmActiveEntryPort OBJECT-TYPE
    SYNTAX  Integer32 (0..2147483647)
    MAX-ACCESS  read-only
    STATUS current
    DESCRIPTION        "The logical port for the DS1 line that the user connected on.
"
    ::= { cpmActiveCallSummaryEntry 10 }

cpmActiveEntryChannel OBJECT-TYPE
    SYNTAX  Integer32 (0..2147483647)
    MAX-ACCESS  read-only
    STATUS current
    DESCRIPTION        "The channel within the DS1 that is allocated to the call.
"
    ::= { cpmActiveCallSummaryEntry 11 }

cpmActiveRemotePhoneNumber OBJECT-TYPE
    SYNTAX DisplayString(SIZE(0..255))
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The remote telephone number.  For a call into the device,
         this is the originating number.  For a call out of the
         device, this is the dialed number.  If not available the 
         string length is zero.
"
    ::= { cpmActiveCallSummaryEntry 12 }

cpmActiveLocalPhoneNumber OBJECT-TYPE
    SYNTAX DisplayString(SIZE(0..255))
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The local telephone number.  For a call into the device,
         this is the dialed number.  For a call out of the
         device, this is the originating number.  If not available 
         the string length is zero.
"
    ::= { cpmActiveCallSummaryEntry 13 }


cpmActiveTTYNumber OBJECT-TYPE
    SYNTAX Integer32
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The TTY number associated with this call.  This 
         information comes from the IOS 'show line' command.
"
    ::= { cpmActiveCallSummaryEntry 14 }


-- cpmCallHistorySummary

cpmCallHistorySummaryTableMaxLength OBJECT-TYPE
    SYNTAX          Integer32 (0..500)
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION        "The upper limit on the number of entries that the
         cpmCallHistoryTable may contain.  A value of 0
         will prevent any history from being retained. When
         this table is full, the oldest entry will be deleted
         and the new one will be created.
"
        DEFVAL  { 100 }
        ::= { cpmCallHistorySummary 1 }
        
cpmCallHistorySummaryRetainTimer  OBJECT-TYPE
    SYNTAX  Integer32 (0..500)
    UNITS   "minutes"
    MAX-ACCESS      read-write
    STATUS current
    DESCRIPTION        "The minimum amount of time that an cpmCallHistoryEntry
         will be maintained before being deleted.  A value of
         0 will prevent any history from being retained, but
         will not prevent callCompletion traps being genarated.
"
        DEFVAL  { 15 }
        ::= { cpmCallHistorySummary 2 }


cpmCallHistorySummaryTable OBJECT-TYPE
    SYNTAX SEQUENCE OF CpmCallHistorySummaryEntry
    MAX-ACCESS not-accessible
    STATUS current
    DESCRIPTION        "The call history summary table is needed to track 
         ended active calls.  This table is needed 
         because modem calls are not in CALL-HISTORY-MIB; 
         the CISCO-ISDN-MIB objects do not contain information 
         about the active calls; and the DIAL-CONTROL_MIB 
         is not yet available.
" 
    ::= { cpmCallHistorySummary 3 }

cpmCallHistorySummaryEntry OBJECT-TYPE
    SYNTAX CpmCallHistorySummaryEntry
    MAX-ACCESS not-accessible
    STATUS current
    DESCRIPTION        "An entry in the Call Summary table.
"
    INDEX { cpmCallDisconnectTimeIndex, 
            cpmCallStartTimeIndex, 
            cpmCallHistorySummaryIndex }
    ::= { cpmCallHistorySummaryTable 1 }

CpmCallHistorySummaryEntry ::= SEQUENCE {
    cpmCallDisconnectTimeIndex TimeStamp,
    cpmCallStartTimeIndex TimeStamp,
    cpmCallHistorySummaryIndex Integer32,
    cpmUserID  DisplayString,
    cpmUserIpAddr IpAddress,
    cpmCallType INTEGER,
    cpmModemSlot Integer32,
    cpmModemPort Integer32,
    cpmCallDuration TimeTicks,
    cpmEntrySlot Integer32,
    cpmEntryPort Integer32,
    cpmEntryChannel Integer32,
    cpmRemotePhoneNumber DisplayString,
    cpmLocalPhoneNumber DisplayString,
    cpmTTYNumber Integer32
    }

cpmCallDisconnectTimeIndex OBJECT-TYPE
    SYNTAX TimeStamp
    MAX-ACCESS not-accessible
    STATUS current
    DESCRIPTION        "The disconnect time of the call.
"
    ::= { cpmCallHistorySummaryEntry 1 }

cpmCallStartTimeIndex OBJECT-TYPE
    SYNTAX TimeStamp
    MAX-ACCESS not-accessible
    STATUS current
    DESCRIPTION        "The start time of the current call.
"
    ::= { cpmCallHistorySummaryEntry 2 }

cpmCallHistorySummaryIndex OBJECT-TYPE
    SYNTAX Integer32 (0..2147483647)
    MAX-ACCESS not-accessible
    STATUS current
    DESCRIPTION        "Arbitrary small integer to distinguish calls that occured
         at the same time tick.
"
    ::= { cpmCallHistorySummaryEntry 3 }

cpmUserID OBJECT-TYPE
    SYNTAX DisplayString(SIZE(0..255))
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The User login ID or zero length string if unavailable.
         This object comes directly from IOS.
"
    ::= { cpmCallHistorySummaryEntry 4 }

cpmUserIpAddr OBJECT-TYPE
    SYNTAX  IpAddress
    MAX-ACCESS  read-only
    STATUS current
    DESCRIPTION        "The IP address of the call or 0.0.0.0 if unavailable.
         This object comes directly from IOS.
"
    ::= { cpmCallHistorySummaryEntry 5 }

cpmCallType OBJECT-TYPE
    SYNTAX INTEGER {
       unknown(1),
       analog(2),
       digital(3),
       v110(4),
       v120(5),
       voice(6)
       }
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The call type:
            unknown  - None of the following 
            analog   - Modem call
            digital  - Digital call
            v110     - V110 Call
            v120     - V120 Call
            voice    - Voice Call
"
    ::= { cpmCallHistorySummaryEntry 6 }

cpmModemSlot OBJECT-TYPE
    SYNTAX     Integer32
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION        "Identification of modem resource allocated to call.
         This is the value of cmSlotIndex from CISCO-MODEM-MGMT-MIB.
         This value along with cpmModemPort uniquely identifies a modem.
         Value is -1 if call does not utilize a modem.
"
    ::= { cpmCallHistorySummaryEntry 7 }
 
cpmModemPort OBJECT-TYPE
    SYNTAX     Integer32
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION        "Identification of modem resource allocated to call.
         This is the value of cmPortIndex from CISCO-MODEM-MGMT-MIB.
         This value along with cpmModemSlot uniquely identifies a modem.
         Value is -1 if call does not utilize a modem.
"
    ::= { cpmCallHistorySummaryEntry 8 }

cpmCallDuration OBJECT-TYPE
    SYNTAX TimeTicks
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The duration of the current call.
"
    ::= { cpmCallHistorySummaryEntry 9 }

cpmEntrySlot OBJECT-TYPE
    SYNTAX  Integer32
    MAX-ACCESS  read-only
    STATUS current
    DESCRIPTION        "The physical system slot in which the DS1 line that the user 
         connected on resides.
"
    ::= { cpmCallHistorySummaryEntry 10 }

cpmEntryPort OBJECT-TYPE
    SYNTAX  Integer32
    MAX-ACCESS  read-only
    STATUS current
    DESCRIPTION        "The logical port for the DS1 line that the user connected on.
"
    ::= { cpmCallHistorySummaryEntry 11 }

cpmEntryChannel OBJECT-TYPE
    SYNTAX  Integer32
    MAX-ACCESS  read-only
    STATUS current
    DESCRIPTION        "The channel within the DS1 that is allocated to the call.
"
    ::= { cpmCallHistorySummaryEntry 12 }


cpmRemotePhoneNumber OBJECT-TYPE
    SYNTAX DisplayString(SIZE(0..255))
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The remote telephone number.  For a call into the device,
         this is the originating number.  For a call out of the
         device, this is the dialed number.  If not available 
         the string length is zero.
"
    ::= { cpmCallHistorySummaryEntry 13 }

cpmLocalPhoneNumber OBJECT-TYPE
    SYNTAX DisplayString(SIZE(0..255))
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The local telephone number.  For a call into the device,
         this is the dialed number.  For a call out of the
         device, this is the originating number. If not available 
         the string length is zero.
"
    ::= { cpmCallHistorySummaryEntry 14 }

cpmTTYNumber OBJECT-TYPE
    SYNTAX Integer32
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The TTY number associated with this call.  This 
         information comes from the IOS 'show line' command.
"
    ::= { cpmCallHistorySummaryEntry 15 }

cpmDS1LoopbackNotifyEnable OBJECT-TYPE
    SYNTAX TruthValue
    MAX-ACCESS read-write
    STATUS current
    DESCRIPTION        "This variable controls the generation of
         cpmDS1LoopbackNotification
  
         When this variable is 'true(1)', generation of
         these notification is enabled. When this
         variable is 'false(2)', generation is disabled

         The default value is 'false(2)'.
        
"
    ::= { cpmDS1LoopbackNotifyConfig 1 }

--
-- Notifications
--
cPopMgmtMIBNotificationPrefix  OBJECT IDENTIFIER ::=
                                 { ciscoPopMgmtMIB 2 }

cpmNotifications               OBJECT IDENTIFIER ::=
                                 { cPopMgmtMIBNotificationPrefix  0 }


cpmDS0BusyoutNotification        NOTIFICATION-TYPE
        OBJECTS {
                cpmDS0BusyoutStatus,
                cpmDS0BusyoutTime,
                cpmDS0BusyoutSource,
                cpmDS0InterfaceIndex
                }
        STATUS  current
        DESCRIPTION            "This notification is sent when there is a state change
             in cpmDS0BusyoutStatus object.
"
       ::= { cpmNotifications 1 }

cpmDS1LoopbackNotification NOTIFICATION-TYPE
        OBJECTS {
                dsx1LineStatus,
                dsx1LineIndex
                }
        STATUS current
        DESCRIPTION            "This notification is sent when there is a state change
             in dsx1LineStatus object of RFC1406-MIB.
"
        ::= { cpmNotifications 2 }


-- conformance information

cpmMIBConformance         OBJECT IDENTIFIER ::= { ciscoPopMgmtMIB 3 }
cpmMIBCompliances         OBJECT IDENTIFIER ::= { cpmMIBConformance 1 }
cpmMIBGroups              OBJECT IDENTIFIER ::= { cpmMIBConformance 2 }


-- compliance statements

cpmMIBCompliance MODULE-COMPLIANCE
    STATUS      obsolete -- superseded by cpmMIBComplianceRev1 
    DESCRIPTION        "The compliance statement used in a PoPM Stack, 
         which implement the Cisco PoP Management MIB
"
    MODULE      -- this module
    MANDATORY-GROUPS { 
                cpmDS0UsageGroup,
                cpmCallFailureGroup,
                cpmActiveCallSummaryGroup,
                cpmCallHistorySummaryGroup
             }
    ::= { cpmMIBCompliances 1 }

cpmMIBComplianceRev1 MODULE-COMPLIANCE
    STATUS      obsolete -- superseded by cpmMIBComplianceRev2
    DESCRIPTION        "The compliance statement used in a PoPM Stack, 
         which implement the Cisco PoP Management MIB
"
    MODULE      -- this module
    MANDATORY-GROUPS {
                cpmDS0UsageGroupRev1,
                cpmCallFailureGroup,
                cpmActiveCallSummaryGroup,
                cpmCallHistorySummaryGroup
             }
    ::= { cpmMIBCompliances 2 }

cpmComplianceRev2 MODULE-COMPLIANCE
    STATUS      obsolete -- superseded by cpmMIBComplianceRev3
    DESCRIPTION        "The compliance statement used in a PoPM Stack, 
         which implement the Cisco PoP Management MIB
"
    MODULE      -- this module
    MANDATORY-GROUPS {
                cpmDS0UsageGroupRev2,
                cpmCallFailureGroup,
                cpmActiveCallSummaryGroup,
                cpmCallHistorySummaryGroup
             }
    ::= { cpmMIBCompliances 3 }

cpmMIBComplianceRev3 MODULE-COMPLIANCE
    STATUS      deprecated
    DESCRIPTION        "The compliance statement used in a PoPM Stack, 
         which implement the Cisco PoP Management MIB
"
    MODULE      -- this module
    MANDATORY-GROUPS {
                cpmDS0UsageGroupRev2,
                cpmCallFailureGroup,
                cpmActiveCallSummaryGroup,
                cpmCallHistorySummaryGroup
             }
     GROUP cpmDS0StatusGroup
           DESCRIPTION              "This group is optional.
"

     GROUP cpmDS1UsageGroup
           DESCRIPTION              "This group is optional.
"

     GROUP cpmSystemGroup
           DESCRIPTION              "This group is optional.
"

     GROUP cpmNotificationGroup
           DESCRIPTION              "This group is mandatory only for systems supporting
               generation of notifications.
"

    ::= { cpmMIBCompliances 4 }


cpmMIBComplianceRev4 MODULE-COMPLIANCE
    STATUS      deprecated 
    DESCRIPTION        "The compliance statement used in a PoPM Stack, 
         which implement the Cisco PoP Management MIB
"
    MODULE      -- this module
    MANDATORY-GROUPS {
                cpmDS0UsageGroupRev2,
                cpmCallFailureGroup,
                cpmActiveCallSummaryGroup,
                cpmCallHistorySummaryGroup,
        cpmCallVolumeGroup
             }
     GROUP cpmDS0StatusGroup
           DESCRIPTION              "This group is optional.
"

     GROUP cpmDS1UsageGroup
           DESCRIPTION              "This group is optional.
"

     GROUP cpmSystemGroup
           DESCRIPTION              "This group is optional.
"
    ::= { cpmMIBCompliances 5 }


cpmMIBComplianceRev5 MODULE-COMPLIANCE
    STATUS      current
    DESCRIPTION        "The compliance statement used in a PoPM Stack,
         which implement the Cisco PoP Management MIB
"
    MODULE      -- this module
    MANDATORY-GROUPS {
                cpmDS0UsageGroupRev2,
                cpmCallFailureGroup,
                cpmActiveCallSummaryGroup,
                cpmCallHistorySummaryGroup,
        cpmCallVolumeGroup
             }
     GROUP cpmDS0StatusGroup
           DESCRIPTION              "This group is optional.
"

     GROUP cpmDS1UsageGroup
           DESCRIPTION              "This group is optional.
"

     GROUP cpmSystemGroup
           DESCRIPTION              "This group is optional.
"

     GROUP cpmDS1LoopbackNotifyConfigGroup
           DESCRIPTION              "This group is optional.
"

     GROUP cpmNotificationGroupRev1
           DESCRIPTION              "This group is optional.
"
    ::= { cpmMIBCompliances 6 }


-- units of conformance

cpmDS0UsageGroup OBJECT-GROUP
    OBJECTS {
         cpmConfiguredType,
         cpmDS0CallType,
         cpmL2Encapsulation,
         cpmCallCount,
         cpmTimeInUse,
         cpmInOctets,
         cpmOutOctets,
         cpmInPackets,
         cpmOutPackets,
         cpmAssociatedInterface,
         cpmISDNCfgBChanInUseForAnalog,
         cpmISDNCfgBChannelsInUse, 
         cpmActiveDS0s,
         cpmPPPCalls, 
         cpmV120Calls, 
         cpmV110Calls
        }
    STATUS obsolete -- superseded by cpmDS0UsageGroupRev1 
    DESCRIPTION        "A collection of objects providing the analog and 
         digital statistics for a DS1.
"
    ::= { cpmMIBGroups 1 }
 
 cpmCallFailureGroup OBJECT-GROUP
    OBJECTS {
         cpmISDNCallsRejected,
         cpmModemCallsRejected,
         cpmISDNCallsClearedAbnormally,
         cpmModemCallsClearedAbnormally,
         cpmISDNNoResource,
         cpmModemNoResource
    }
    STATUS current
    DESCRIPTION            "A collection of objects providing aggregate 
             totals of call failures
"
    ::= { cpmMIBGroups 2 }
 
cpmActiveCallSummaryGroup OBJECT-GROUP
    OBJECTS {
         cpmActiveUserID,
         cpmActiveCallType,
         cpmActiveUserIpAddr,
         cpmActiveModemSlot,
         cpmActiveModemPort,
         cpmActiveCallDuration,
         cpmActiveEntrySlot,
         cpmActiveEntryPort,
         cpmActiveEntryChannel,
         cpmActiveRemotePhoneNumber,
         cpmActiveLocalPhoneNumber,
         cpmActiveTTYNumber
        }
    STATUS current
    DESCRIPTION        "A collection of objects providing the summary of the 
         currently active calls.
"
    ::= { cpmMIBGroups 3 }
 
cpmCallHistorySummaryGroup OBJECT-GROUP
    OBJECTS {
         cpmCallHistorySummaryTableMaxLength,
         cpmCallHistorySummaryRetainTimer,
         cpmUserID,
         cpmUserIpAddr,
         cpmCallType,
         cpmModemSlot,
         cpmModemPort,
         cpmCallDuration,
         cpmEntrySlot,
         cpmEntryPort,
         cpmEntryChannel,
         cpmRemotePhoneNumber,
         cpmLocalPhoneNumber,
         cpmTTYNumber
    }
    STATUS current
    DESCRIPTION        "A collection of objects providing the summary of calls
         that were recently terminated.
"
    ::= { cpmMIBGroups 4 }
 
cpmDS0UsageGroupRev1 OBJECT-GROUP
    OBJECTS {
         cpmConfiguredType,
         cpmDS0CallType,
         cpmL2Encapsulation,
         cpmCallCount,
         cpmTimeInUse,
         cpmInOctets,
         cpmOutOctets,
         cpmInPackets,
         cpmOutPackets,
         cpmAssociatedInterface,
         cpmISDNCfgBChanInUseForAnalog,
         cpmISDNCfgBChannelsInUse,
         cpmActiveDS0s,
         cpmPPPCalls,
         cpmV120Calls,
         cpmV110Calls,
         cpmActiveDS0sHighWaterMark,
         cpmDS1ActiveDS0s,
         cpmDS1ActiveDS0sHighWaterMark,
         cpmSW56CfgBChannelsInUse
        }
    STATUS obsolete -- superseded by cpmDS0UsageGroupRev2
    DESCRIPTION        "A collection of objects providing the analog and
         digital statistics for a DS1.
"
    ::= { cpmMIBGroups 5 }

cpmDS0UsageGroupRev2 OBJECT-GROUP
    OBJECTS {
         cpmConfiguredType,
         cpmDS0CallType,
         cpmL2Encapsulation,
         cpmCallCount,
         cpmTimeInUse,
         cpmInOctets,
         cpmOutOctets,
         cpmInPackets,
         cpmOutPackets,
         cpmAssociatedInterface,
         cpmISDNCfgBChanInUseForAnalog,
         cpmISDNCfgBChannelsInUse,
         cpmActiveDS0s,
         cpmPPPCalls,
         cpmV120Calls,
         cpmV110Calls,
         cpmActiveDS0sHighWaterMark,
         cpmDS1ActiveDS0s,
         cpmDS1ActiveDS0sHighWaterMark,
         cpmSW56CfgBChannelsInUse,
         cpmISDNCfgBChanInUseForVoice,
         cpmCASCfgBChanInUseForVoice
        }
    STATUS current
    DESCRIPTION        "A collection of objects providing the analog and
         digital statistics for a DS1.
"
    ::= { cpmMIBGroups 6 }

cpmDS1UsageGroup OBJECT-GROUP
    OBJECTS {
         cpmDS1TotalAnalogCalls,
         cpmDS1TotalDigitalCalls,
         cpmDS1TotalV110Calls,
         cpmDS1TotalV120Calls,
         cpmDS1TotalCalls,
         cpmDS1TotalTimeInUse,
         cpmDS1CurrentIdle,
         cpmDS1CurrentOutOfService,
         cpmDS1CurrentBusyout,
         cpmDS1InOctets,
         cpmDS1OutOctets,
         cpmDS1InPackets,
         cpmDS1OutPackets
        }
    STATUS current
    DESCRIPTION        "A collection of objects providing statistics aggregation
         across DS0s within a DS1.
"
    ::= { cpmMIBGroups 7 }

cpmSystemGroup OBJECT-GROUP
    OBJECTS {
         cpmISDNCfgActiveDChannels,
         cpmISDNCfgBChannelsTimeInUse,
         cpmISDNCfgBChannelsTimeInUseAnlg,
         cpmISDNCfgBChannelCalls,
         cpmISDNCfgBChannelAnalogCalls,
         cpmTotalISDNSyncPPPCalls
        }
    STATUS current
    DESCRIPTION        "A collection of objects providing statistics aggregation
         for the entire system.
"
    ::= { cpmMIBGroups 8 }
  
cpmDS0StatusGroup OBJECT-GROUP
    OBJECTS {
         cpmDS0BusyoutNotifyEnable,
         cpmDS0OperStatus,
         cpmDS0BusyoutAdminStatus,
         cpmDS0BusyoutAllow,
         cpmDS0BusyoutStatus,
         cpmDS0BusyoutSource,
         cpmDS0BusyoutTime,
         cpmDS0ConfigFunction,
         cpmDS0InterfaceIndex
        }
    STATUS current
    DESCRIPTION        "A collection of objects providing the status for a DS0.
"
    ::= { cpmMIBGroups 9 }

cpmNotificationGroup NOTIFICATION-GROUP
    NOTIFICATIONS { cpmDS0BusyoutNotification }
    STATUS deprecated
    DESCRIPTION        "The collection of notifications
        
"
    ::= { cpmMIBGroups 10 }

cpmDS1LoopbackNotifyConfigGroup OBJECT-GROUP
      OBJECTS {
          cpmDS1LoopbackNotifyEnable
      }
      STATUS current
      DESCRIPTION          "A collection of objects providing the
           notification configuration
          
"
      ::= { cpmMIBGroups 11 }


cpmCallVolumeGroup OBJECT-GROUP
    OBJECTS {
    cpmCallVolSuccISDNDigital,
    cpmCallVolAnalogCallClearedNormally
    }
    STATUS current
    DESCRIPTION            "A collection of objects providing aggregate 
             totals of call successfully completed
"
    ::= { cpmMIBGroups 12 }

cpmNotificationGroupRev1 NOTIFICATION-GROUP
    NOTIFICATIONS {
             cpmDS0BusyoutNotification,
             cpmDS1LoopbackNotification
             }
    STATUS current
    DESCRIPTION        "The collection of notifications
        
"
    ::= { cpmMIBGroups 13 }
END
 
 
 





                
                
            
			
        
   
Help  |  Feedback