Guest

Tools & Resources

SNMP Object Navigator


CISCO-STUN-MIB

View compiling dependencies for other MIBS by clearing the page and selecting another MIB.

Compile the MIB

Before you can compile CISCO-STUN-MIB , you need to compile the MIBs listed below in the order listed.

Download all of these MIBs (Warning: does not include non-Cisco MIBs) or view details about each MIB below.

If you are using Internet Explorer click here.

      MIB Name   Version 1   Version 2   Dependencies
    1. SNMPv2-SMI Download  |  Download  |  View Dependencies
    2. SNMPv2-TC Download  |  Download  |  View Dependencies
    3. SNMPv2-CONF Not Required  |  Download  |  View Dependencies
    4. SNMPv2-MIB Download  |  Download  |  View Dependencies
    5. IANAifType-MIB Download  |  Download  |  View Dependencies
    6. IF-MIB Download  |  Download  |  View Dependencies
    7. CISCO-SMI Download  |  Download  |  View Dependencies
    8. RFC-1212   Non-Cisco MIB   |  Non-Cisco MIB   |  -
    9. SNMPv2-SMI-v1   Non-Cisco MIB   |  Non-Cisco MIB   |  -
    10. RFC-1215   Non-Cisco MIB   |  Non-Cisco MIB   |  -
    11. SNMPv2-TC-v1   Non-Cisco MIB   |  Non-Cisco MIB   |  -
    12. CISCO-STUN-MIB Download  |  Download  | 

More Downloads

OID File: CISCO-STUN-MIB.oid

Extra Information

None

MIB Contents

This is the SMI version 2 of the MIB. Click here to see the SMI version 1
        
		
            
                
                    


-- *****************************************************************
-- CISCO-STUN-MIB.my: Cisco STUN MIB
--
-- April 1995, Bob Clouston
--
-- Copyright (c) 1995 by cisco Systems, Inc.
-- All rights reserved.
-- *****************************************************************
--

CISCO-STUN-MIB DEFINITIONS ::= BEGIN

IMPORTS
	MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE,
	Counter32,  IpAddress
		FROM SNMPv2-SMI
	MODULE-COMPLIANCE, OBJECT-GROUP
		FROM SNMPv2-CONF
	ifIndex, InterfaceIndex
		FROM IF-MIB
	TruthValue
		FROM SNMPv2-TC 
	ciscoMgmt
		FROM CISCO-SMI;


ciscoStunMIB MODULE-IDENTITY
	LAST-UPDATED	"9508210000Z"
	ORGANIZATION	"Cisco Systems, Inc."
	CONTACT-INFO
		"	Cisco Systems
			Customer Service
                     
		Postal: 170 W. Tasman Drive
			San Jose, CA 95134
			USA

		   Tel: +1 800 553-NETS
		e-mail: cs-snmp@cisco.com"
	DESCRIPTION		"The MIB module for serial Tunneling.

   Overview of STUN MIB
  
   MIB description
   
   The STUN MIB provides the configuration and operational information 
   on Cisco's serial tunnelling implementation.  The following entities
   are managed:
    1) Global STUN information
    2) STUN groups
    3) STUN ports
    4) STUN routes
  
   The following example configuration shows how the STUN MIB returns
   STUN information, from either CISCO A or CISCO B.
  
    HOST == SDLC == Cisco A == IP Network == Cisco B == SDLC  == SDLC
            line                                        line     device
  
   1) The STUN global entry identifies the IP address by which the
      router is known to other STUN peers.
   2) The STUN group table identifies the STUN group number and protocol
      type that Cisco A and Cisco B use to route SDLC traffic over the 
      IP network.  The table contains an entry for each STUN group
      defined on the router.
   3) The STUN port table identifies the serial interface to the SDLC 
      line for which the router is doing serial tunnelling.  The MIB also
      identifies the STUN group this interface is defined for, and
      identifies the default routing for unrecognized SDLC addresses.
      There is a port entry for each STUN-enabled interface on the router.
   4) The STUN route table has an entry for each address defined for
      routing within the STUN group, and an entry for the default routing
      if the 'stun route all' command is configured.  The route entry
      includes identification of the STUN peer, priority, state, whether
      local acknowledgment is enabled, and packet and byte counters.
   
"
	REVISION	"9508210000Z"
	DESCRIPTION		"Added revision clause, formatting cleanup.
"
	REVISION	"9503170000Z"
	DESCRIPTION		"Initial version of this MIB module.
"
	::= { ciscoMgmt 30 }

stunObjects   OBJECT IDENTIFIER ::= { ciscoStunMIB 1}
stunGlobal    OBJECT IDENTIFIER ::= { stunObjects 1}
stunGroups    OBJECT IDENTIFIER ::= { stunObjects 2}
stunPorts     OBJECT IDENTIFIER ::= { stunObjects 3}
stunRoutes    OBJECT IDENTIFIER ::= { stunObjects 4}

-- ******************************************************************
-- * global values for router
-- ******************************************************************
  
stunIPAddr OBJECT-TYPE
    SYNTAX IpAddress
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The configured IP address used for all serial tunnelling
         in this router.
"
    ::= { stunGlobal 1 }

-- ******************************************************************
-- * stun Group Table
-- ******************************************************************

stunGroupTable OBJECT-TYPE
    SYNTAX SEQUENCE OF StunGroupEntry
    MAX-ACCESS not-accessible
    STATUS current
    DESCRIPTION        "A table of entries representing STUN groups configured on the
         router.  Each STUN-enabled interface is assigned to a STUN
         group, and packets can only travel between STUN-enabled
         interfaces in the same group.
"
    ::= { stunGroups 1 }

stunGroupEntry OBJECT-TYPE
    SYNTAX StunGroupEntry
    MAX-ACCESS not-accessible
    STATUS current
    DESCRIPTION        "Status and parameter values for a group.
"
    INDEX { stunGroupIndex }
    ::= { stunGroupTable 1 }

StunGroupEntry ::=
    SEQUENCE {
        stunGroupIndex
            INTEGER,
        stunProtocolType
            INTEGER
    }


stunGroupIndex OBJECT-TYPE
    SYNTAX INTEGER (1..255)
    MAX-ACCESS not-accessible
    STATUS current
    DESCRIPTION        "The configured STUN group number.
"
    ::= { stunGroupEntry 1 }

stunProtocolType OBJECT-TYPE
    SYNTAX INTEGER
     {
      basic(1),   -- non-SDLC, such as HDLC 
      sdlc(2),    -- SDLC protocol
      sdlctg(3),  -- SNA transmission group
      custom(4)    -- customer-defined protocol
     }
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The protocol type for this STUN group.
"
    ::= { stunGroupEntry 2 }

-- ******************************************************************
-- * stun Port Table
-- ******************************************************************

stunPortTable OBJECT-TYPE
    SYNTAX SEQUENCE OF StunPortEntry
    MAX-ACCESS not-accessible
    STATUS current
    DESCRIPTION        "A list of STUN-enabled interfaces (ports).
"
    ::= { stunPorts 1 }

stunPortEntry OBJECT-TYPE
    SYNTAX StunPortEntry
    MAX-ACCESS not-accessible
    STATUS current
    DESCRIPTION        "Status and parameter values for a STUN port.
"
    INDEX { ifIndex }
    ::= { stunPortTable 1 }

StunPortEntry ::=
    SEQUENCE {
        stunPortGroupIndex
            INTEGER,
        stunPortDefaultPeerType
            INTEGER,
        stunPortDefaultPeerIP   
            IpAddress,
        stunPortDefaultPeerSerialInterface  
            InterfaceIndex
    }

stunPortGroupIndex OBJECT-TYPE
    SYNTAX INTEGER (1..255)
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The group number to which the stun port
         belongs.  Frames will only be routed to other 
         ports (on this or another router) in the same 
         stun group.  This group must match a stunGroupIndex
         in the stunGroupTable.
"
    ::= { stunPortEntry 1 }


stunPortDefaultPeerType OBJECT-TYPE
    SYNTAX INTEGER 
     { 
      other(1), 
      ip(2), 
      direct(3), 
      frameRelay(4) 
     }
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The type of identification of the default partner 
         for unrecognized addresses. If there
         is no default route then the stunRouteType
         field of stunPortDefaultRemote is 'other'.
         If ip then the value is in stunRouteIP; if serial or
         serialDirect then the value is in stunRouteSerial.
"
    ::= { stunPortEntry 2 }

stunPortDefaultPeerIP OBJECT-TYPE
    SYNTAX IpAddress
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The ip address of the remote default STUN partner,
         for unrecognized addresses.  
         0.0.0.0 is returned if the default route type is not ip.
"
    ::= { stunPortEntry 3 }

stunPortDefaultPeerSerialInterface OBJECT-TYPE
    SYNTAX InterfaceIndex
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "If stunRouteType is serial then this is the 
         serial interface index of the point-to-point
         link to the remote partner; 
         if stunRouteType is serialDirect then the 
         partner is in the local STUN.
         if stunRouteType is ip then this field is
         0.
"
    ::= { stunPortEntry 4 }

-- ******************************************************************
-- * Route Table
-- ******************************************************************

stunRouteTable OBJECT-TYPE
    SYNTAX   SEQUENCE OF StunRouteEntry
    MAX-ACCESS   not-accessible
    STATUS   current
    DESCRIPTION       "A table containing information about specific SDLC
        addresses.  There is one table entry for each SDLC
        address configured by the STUN ROUTE command.
"
    ::= { stunRoutes 1 }

stunRouteEntry OBJECT-TYPE
    SYNTAX   StunRouteEntry
    MAX-ACCESS   not-accessible
    STATUS   current
    DESCRIPTION       "The information regarding a single STUN address.
"
    INDEX { stunGroupIndex, stunRouteStationAddress }
    ::= { stunRouteTable 1 }


StunRouteEntry ::=
    SEQUENCE {
         stunRouteStationAddress
            INTEGER,
         stunRouteType
            INTEGER,
         stunRouteRemoteIP   
            IpAddress,
         stunRouteSerialInterface  
            InterfaceIndex,
         stunRoutePriority
            INTEGER,
         stunRoutePeerState
            INTEGER,
         stunRouteLocalAck
            TruthValue,
         stunRouteRxPackets
            Counter32,
         stunRouteTxPackets
            Counter32,
         stunRouteRxBytes
            Counter32,
         stunRouteTxBytes
            Counter32
    }

stunRouteStationAddress OBJECT-TYPE
    SYNTAX INTEGER(1..256)
    MAX-ACCESS not-accessible
    STATUS current
    DESCRIPTION        "The poll address of the station.  256 indicates the ALL parameter
         on the STUN ROUTE command, which is the route for all 
         unrecognized addresses.
" 
    ::= { stunRouteEntry 1 }

stunRouteType OBJECT-TYPE
    SYNTAX INTEGER 
     { 
      other(1), 
      ip(2), 
      direct(3), 
      frameRelay(4) 
     }
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The type of identification of the remote partner.
"
    ::= { stunRouteEntry 2 }

stunRouteRemoteIP OBJECT-TYPE
    SYNTAX IpAddress
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The ip address of the remote STUN partner. 
         0.0.0.0 if partner type is not ip.
"
    ::= { stunRouteEntry 3 }

stunRouteSerialInterface OBJECT-TYPE
    SYNTAX InterfaceIndex
    MAX-ACCESS read-only 
    STATUS current
    DESCRIPTION        "The local interface index to the remote partner.
         0 is returned if the partner type is not direct or frameRelay.
"
   ::= { stunRouteEntry 4 }

stunRoutePriority OBJECT-TYPE
    SYNTAX INTEGER 
     {
      low(1), 
      normal(2), 
      medium(3), 
      high(4)
     }
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The priority with which this station's traffic will
         be routed across the network.
"
    ::= { stunRouteEntry 5 }
            
stunRoutePeerState OBJECT-TYPE
    SYNTAX INTEGER 
     {
      dead(1), 
      closed(2), 
      opening(3), 
      openWait(4),
      connected(5), 
      direct(6)
     }
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "The state of the peer connection through the
         STUN tunnel.
"
    ::= { stunRouteEntry 6 }
            
stunRouteLocalAck OBJECT-TYPE
    SYNTAX TruthValue
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION       "Indicates if the STUN connection is locally acknowledged.       
        TRUE-> STUN connection is locally acknowledged
        FALSE-> STUN connection is not locally acknowledged
       
" 
    ::= { stunRouteEntry 7 }
    
stunRouteRxPackets OBJECT-TYPE
    SYNTAX Counter32
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "Count of frames received from the serial
         interface with this station's address.
"
    ::= { stunRouteEntry 8 }

stunRouteTxPackets OBJECT-TYPE
    SYNTAX Counter32
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "Count of frames transmitted at the serial
         interface with this station's address.
"
    ::= { stunRouteEntry 9 }

stunRouteRxBytes OBJECT-TYPE
    SYNTAX Counter32
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "Count of bytes received from the serial
         interface with this station's address.
"
    ::= { stunRouteEntry 10 }

stunRouteTxBytes OBJECT-TYPE
    SYNTAX Counter32
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION        "Count of bytes transmitted at the serial
         interface with this station's address.
"
    ::= { stunRouteEntry 11 }

-- *************************************************************************
-- * STUN notifications               
-- *************************************************************************

stunNotificationPrefix OBJECT IDENTIFIER ::= { ciscoStunMIB 2 }
stunNotifications OBJECT IDENTIFIER ::= { stunNotificationPrefix 0 }

stunPeerStateChangeNotification NOTIFICATION-TYPE
     OBJECTS { stunRoutePeerState }
     STATUS      current
     DESCRIPTION        "This notification indicates that the state of a STUN route
         has transitioned to active (connected or direct) or inactive
         (dead or closed).
"
     ::= { stunNotifications 1 }
     

-- *************************************************************************
-- * Conformance Information
-- *************************************************************************
--

stunMibConformance   OBJECT IDENTIFIER ::= { ciscoStunMIB 3 }
stunMibCompliances   OBJECT IDENTIFIER ::= { stunMibConformance 1 }
stunMibGroups        OBJECT IDENTIFIER ::= { stunMibConformance 2 }
--
-- *************************************************************************
-- * Compliance Statements
-- *************************************************************************
stunMibCompliance    MODULE-COMPLIANCE
        STATUS current
        DESCRIPTION                "The compliance statement for STUN.
"
        MODULE  -- this module
                MANDATORY-GROUPS {
                        stunGlobalGroup,
			stunGroupGroup,
                        stunPortGroup,
                        stunRouteGroup
		}
         ::= { stunMibCompliances 1 }
         
stunGlobalGroup OBJECT-GROUP
        OBJECTS {
                stunIPAddr
        }
        STATUS current
        DESCRIPTION                "A collection of objects providing global STUN information.
"
        ::= { stunMibGroups 1}
         
stunGroupGroup OBJECT-GROUP
        OBJECTS {
                stunProtocolType
        }
        STATUS current
        DESCRIPTION                "A collection of objects providing information about 
                 STUN groups .
"
        ::= { stunMibGroups 2 }

stunPortGroup OBJECT-GROUP
        OBJECTS {
                stunPortGroupIndex,
                stunPortDefaultPeerType,
                stunPortDefaultPeerIP,
                stunPortDefaultPeerSerialInterface
        }
        STATUS current
        DESCRIPTION                "A collection of objects providing information about
                 STUN enabled interfaces.
"
        ::= { stunMibGroups 3}
stunRouteGroup OBJECT-GROUP
        OBJECTS {
                stunRouteType,
                stunRouteRemoteIP,
                stunRouteSerialInterface,
                stunRoutePriority,
                stunRoutePeerState,
                stunRouteLocalAck,
                stunRouteRxPackets,
                stunRouteTxPackets,
                stunRouteRxBytes,
                stunRouteTxBytes
        }
        STATUS current
        DESCRIPTION                "A collection of objects providing information about
                 STUN defined routes.
"
        ::= { stunMibGroups 4}
END





                
                
            
			
        
   
Help  |  Feedback