 |
|
|
|
|
CISCO-CONFIG-MAN-MIB
View compiling dependencies for other MIBS by clearing the page and selecting another MIB.
Compile the MIB
Before you can compile CISCO-CONFIG-MAN-MIB , you need to compile the MIBs listed below in the order listed.
Download all of these MIBs (Warning: does not include non-Cisco MIBs) or view details about each MIB below.
If you are using Internet Explorer click here.
| MIB Name |
|
Version 1 |
|
Version 2 |
|
Dependencies |
| 1. SNMPv2-SMI |
|
Download | | | Download | | | View Dependencies |
| 2. SNMPv2-TC |
|
Download | | | Download | | | View Dependencies |
| 3. CISCO-SMI |
|
Download | | | Download | | | View Dependencies |
| 4. SNMPv2-CONF |
|
Not Required | | | Download | | | View Dependencies |
| 5. CISCO-TC |
|
Download | | | Download | | | View Dependencies |
| 6. INET-ADDRESS-MIB |
|
Download | | | Download | | | View Dependencies |
| 7. SNMP-FRAMEWORK-MIB |
|
Download | | | Download | | | View Dependencies |
| 8. RFC1155-SMI | Non-Cisco MIB | | | Non-Cisco MIB | | | - | |
| 9. RFC-1212 | Non-Cisco MIB | | | Non-Cisco MIB | | | - | |
| 10. RFC-1215 | Non-Cisco MIB | | | Non-Cisco MIB | | | - | |
| 11. SNMPv2-TC-v1 | Non-Cisco MIB | | | Non-Cisco MIB | | | - | |
| 12. CISCO-CONFIG-MAN-MIB |
|
Download | | | Download | | |
More Downloads
| OID File: | CISCO-CONFIG-MAN-MIB.oid |
| Capability File: | CISCO-CONFIG-MAN-CAPABILITY |
Extra Information
None
MIB Contents
This is the SMI version 2 of the MIB. Click here to see the SMI version 1
-- *****************************************************************
-- CISCO-CONFIG-MAN-MIB.my: Configuration Management MIB
--
-- April 1995, Bob Stewart
--
-- Copyright (c) 1995-1996 by cisco Systems, Inc.
-- All rights reserved.
--
-- *****************************************************************
CISCO-CONFIG-MAN-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
NOTIFICATION-TYPE,
TimeTicks,
Integer32,
Counter32,
IpAddress
FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
DisplayString,
TEXTUAL-CONVENTION
FROM SNMPv2-TC
ciscoMgmt
FROM CISCO-SMI;
ciscoConfigManMIB MODULE-IDENTITY
LAST-UPDATED "9511280000Z"
ORGANIZATION "Cisco Systems, Inc."
CONTACT-INFO
" Cisco Systems
Customer Service
Postal: 170 W Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
E-mail: cs-snmp@cisco.com"
DESCRIPTION "Configuration management MIB.
The MIB represents a model of configuration data that
exists in various locations:
running in use by the running system
terminal operator's mind or attached hardware
local saved locally in NVRAM or flash
remote saved to some server on the network
Although some of the system functions that relate here
can be used for general file storage and transfer, this
MIB intends to include only such operations as clearly
relate to configuration. Its primary emphasis is to
track changes and saves of the running configuration.
As saved data moves further from startup use, such as
into different local flash files or onto the network,
tracking becomes difficult to impossible, so the MIB's
interest and functions are confined in that area."
REVISION "9511280000Z"
DESCRIPTION "Initial version of this MIB module."
::= { ciscoMgmt 43 }
ciscoConfigManMIBObjects OBJECT IDENTIFIER ::= { ciscoConfigManMIB 1 }
ccmHistory OBJECT IDENTIFIER ::= { ciscoConfigManMIBObjects 1 }
-- Textual Conventions
HistoryEventMedium ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION "The source or destination of a configuration change,
save, or copy.
erase erasing destination (source only)
running live operational data
commandSource the command source itself
startup what the system will use next reboot
local local NVRAM or flash
networkTftp network host via Trivial File Transfer
networkRcp network host via Remote Copy
"
SYNTAX INTEGER { erase(1), commandSource(2), running(3),
startup(4), local(5),
networkTftp(6), networkRcp(7) }
-- Configuration History
ccmHistoryRunningLastChanged OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The value of sysUpTime when the running configuration
was last changed.
If the value of ccmHistoryRunningLastChanged is greater than
ccmHistoryRunningLastSaved, the configuration has been
changed but not saved."
::= { ccmHistory 1 }
ccmHistoryRunningLastSaved OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The value of sysUpTime when the running configuration
was last saved (written).
If the value of ccmHistoryRunningLastChanged is greater than
ccmHistoryRunningLastSaved, the configuration has been
changed but not saved.
What constitutes a safe saving of the running
configuration is a management policy issue beyond the
scope of this MIB. For some installations, writing the
running configuration to a terminal may be a way of
capturing and saving it. Others may use local or
remote storage. Thus ANY write is considered saving
for the purposes of the MIB."
::= { ccmHistory 2 }
ccmHistoryStartupLastChanged OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The value of sysUpTime when the startup configuration
was last written to. In general this is the
default configuration used when cold starting the
system. It may have been changed by a save of the
running configuration or by a copy from elsewhere."
::= { ccmHistory 3 }
ccmHistoryMaxEventEntries OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The maximum number of entries that can be held in
ccmHistoryEventTable.
The recommended value for implementations is 10."
::= { ccmHistory 4 }
ccmHistoryEventEntriesBumped OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The number of times the oldest entry in ccmHistoryEventTable
was deleted to make room for a new entry."
::= { ccmHistory 5 }
ccmHistoryEventTable OBJECT-TYPE
SYNTAX SEQUENCE OF CcmHistoryEventEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A table of configuration events on this router."
::= { ccmHistory 6 }
ccmHistoryEventEntry OBJECT-TYPE
SYNTAX CcmHistoryEventEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Information about a configuration event on this router."
INDEX { ccmHistoryEventIndex }
::= { ccmHistoryEventTable 1 }
CcmHistoryEventEntry ::=
SEQUENCE {
ccmHistoryEventIndex
Integer32,
ccmHistoryEventTime
TimeTicks,
ccmHistoryEventCommandSource
INTEGER,
ccmHistoryEventConfigSource
HistoryEventMedium,
ccmHistoryEventConfigDestination
HistoryEventMedium,
ccmHistoryEventTerminalType
INTEGER,
ccmHistoryEventTerminalNumber
Integer32,
ccmHistoryEventTerminalUser
DisplayString,
ccmHistoryEventTerminalLocation
DisplayString,
ccmHistoryEventCommandSourceAddress
IpAddress,
ccmHistoryEventVirtualHostName
DisplayString,
ccmHistoryEventServerAddress
IpAddress,
ccmHistoryEventFile
DisplayString,
ccmHistoryEventRcpUser
DisplayString
}
ccmHistoryEventIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A monotonically increasing integer for the sole purpose of
indexing events. When it reaches the maximum value, an
extremely unlikely event, the agent wraps the value back
to 1 and may flush existing entries."
::= { ccmHistoryEventEntry 1 }
ccmHistoryEventTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The value of sysUpTime when the event occurred."
::= { ccmHistoryEventEntry 2 }
ccmHistoryEventCommandSource OBJECT-TYPE
SYNTAX INTEGER { commandLine(1), snmp(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The source of the command that instigated the event."
::= { ccmHistoryEventEntry 3 }
ccmHistoryEventConfigSource OBJECT-TYPE
SYNTAX HistoryEventMedium
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The configuration data source for the event."
::= { ccmHistoryEventEntry 4 }
ccmHistoryEventConfigDestination OBJECT-TYPE
SYNTAX HistoryEventMedium
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The configuration data destination for the event."
::= { ccmHistoryEventEntry 5 }
ccmHistoryEventTerminalType OBJECT-TYPE
SYNTAX INTEGER {
notApplicable(1),
unknown(2),
console(3),
terminal(4),
virtual(5),
auxiliary(6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION "If ccmHistoryEventCommandSource is 'commandLine',
the terminal type, otherwise 'notApplicable'."
::= { ccmHistoryEventEntry 6 }
ccmHistoryEventTerminalNumber OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "If ccmHistoryEventCommandSource is 'commandLine',
the terminal number. The value is -1 if not available
or not applicable."
::= { ccmHistoryEventEntry 7 }
ccmHistoryEventTerminalUser OBJECT-TYPE
-- ??? Check max size.
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION "If ccmHistoryEventCommandSource is 'commandLine',
the name of the logged in user. The length is zero if
not available or not applicable."
::= { ccmHistoryEventEntry 8 }
ccmHistoryEventTerminalLocation OBJECT-TYPE
-- ??? Check max size.
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION "If ccmHistoryEventCommandSource is 'commandLine',
the hard-wired location of the terminal or the remote host
for an incoming connection. The length is zero if not
available or not applicable."
::= { ccmHistoryEventEntry 9 }
ccmHistoryEventCommandSourceAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION "If ccmHistoryEventTerminalType is 'virtual', the internet
address of the connected system.
If ccmHistoryEventCommandSource is 'snmp', the internet
address of the requester.
The value is 0.0.0.0 if not available or not applicable."
::= { ccmHistoryEventEntry 10 }
ccmHistoryEventVirtualHostName OBJECT-TYPE
-- ??? Check max size.
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION "If ccmHistoryEventTerminalType is 'virtual', the host
name of the connected system. The length is zero if
not available or not applicable."
::= { ccmHistoryEventEntry 11 }
ccmHistoryEventServerAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION "If ccmHistoryEventConfigSource or
ccmHistoryEventConfigDestination is 'networkTftp' or
'networkRcp', the internet address of the storage file
server. The value is 0.0.0.0 if not applicable or not
available."
::= { ccmHistoryEventEntry 12 }
ccmHistoryEventFile OBJECT-TYPE
-- ??? Check max size.
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION "If ccmHistoryEventConfigSource or
ccmHistoryEventConfigDestination is 'networkTftp' or
'networkRcp', the configuration file name at the
storage file server. The length is zero if not
available or not applicable."
::= { ccmHistoryEventEntry 13 }
ccmHistoryEventRcpUser OBJECT-TYPE
-- ??? Check max size.
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION "If ccmHistoryEventConfigSource or
ccmHistoryEventConfigDestination is 'networkRcp', the
remote user name. The length is zero if not applicable
or not available."
::= { ccmHistoryEventEntry 14 }
-- Notifications
ciscoConfigManMIBNotificationPrefix OBJECT IDENTIFIER ::= { ciscoConfigManMIB 2 }
ciscoConfigManMIBNotifications OBJECT IDENTIFIER ::= { ciscoConfigManMIBNotificationPrefix 0 }
ciscoConfigManEvent NOTIFICATION-TYPE
OBJECTS { ccmHistoryEventCommandSource,
ccmHistoryEventConfigSource,
ccmHistoryEventConfigDestination }
STATUS current
DESCRIPTION "Notification of a configuration management event as
recorded in ccmHistoryEventTable."
::= { ciscoConfigManMIBNotifications 1 }
-- Conformance
ciscoConfigManMIBConformance OBJECT IDENTIFIER ::= { ciscoConfigManMIB 3 }
ciscoConfigManMIBCompliances OBJECT IDENTIFIER ::= { ciscoConfigManMIBConformance 1 }
ciscoConfigManMIBGroups OBJECT IDENTIFIER ::= { ciscoConfigManMIBConformance 2 }
-- Compliance
ciscoConfigManMIBCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION "The compliance statement for entities which implement
the Cisco Configuration Management MIB"
MODULE -- this module
MANDATORY-GROUPS { ciscoConfigManHistoryGroup }
::= { ciscoConfigManMIBCompliances 1 }
-- Units of Conformance
ciscoConfigManHistoryGroup OBJECT-GROUP
OBJECTS {
ccmHistoryRunningLastChanged,
ccmHistoryRunningLastSaved,
ccmHistoryStartupLastChanged,
ccmHistoryMaxEventEntries,
ccmHistoryEventEntriesBumped,
ccmHistoryEventTime,
ccmHistoryEventCommandSource,
ccmHistoryEventConfigSource,
ccmHistoryEventConfigDestination,
ccmHistoryEventTerminalType,
ccmHistoryEventTerminalNumber,
ccmHistoryEventTerminalUser,
ccmHistoryEventTerminalLocation,
ccmHistoryEventCommandSourceAddress,
ccmHistoryEventVirtualHostName,
ccmHistoryEventServerAddress,
ccmHistoryEventFile,
ccmHistoryEventRcpUser
}
STATUS current
DESCRIPTION "Configuration history."
::= { ciscoConfigManMIBGroups 1 }
END
|
|
If you still need help...
Try these TAC resources
Access support information for your product in the
Product Pages.
Find information on your technology of interest in the
Technology Pages.
View the full index of
TAC tools.
Request live assistance
If you cannot find answers to your questions,
open a service request with the Cisco Technical Assistance Center (TAC).