|
|
Recommended Content
Cisco Software CentralGet quotes, place orders, register and manage licenses, and download software, upgrades, and patches. Log in required.
|
1 - 10 of
5,912 results for
Active and Standby Control Card States During a WAN Switch Software Upgrade
|
|
|
|
This document describes the Cisco recommended 34 point process for a successful IPX, IGX 8400 Series Switch, or BPX 8600 Series Switch software upgrade.
www.cisco.com/en/US/products/sw/ps2346/ps99/products_tech_note09186a0080094c67.shtml
17 Apr 2009
This document explains the step-by-step procedures to upgrade the software images on Catalyst 6000/6500 Series Switches with redundant Supervisor Engines that run in Hybrid mode (Cisco Catalyst Operating System (CatOS) on Supervisor Engine, and Cisco IOS on Multilayer Switch Feature...
References:
117
TAC
|
2
Support Community
-
View All
www.cisco.com/en/US/products/hw/switches/ps708/products_configuration_example09186a0080a98f3c.shtml
08 Aug 2008
...request after SF switch CSCdp93955 Swlog 532 when doing a snmpwalk on the...programming 2ndary card in Y-Red set...reports active state when the back...available CSCdr51105 Software error 30 is logged...command CSCdr79123 During routing delay...differently during upgrade vs provision...CSCdm31518 "Active CC failure (EEPROM, SAR) and standby unlock or reseat...CSCdp53961 Control card mastership...card errors on active. Card has state...
www.cisco.com/en/US/docs/switches/wan/bpx/release/notes/9238rn.html
14 Apr 2008
...Hardware Revision A, B, C, D...command is issued during the switch software upgrade process, the...1 Removed Info Standby NPC 1 Update Completed...mode causes all cards, except the processor...the standby and active NPC-32s (Node...bus, a "C" (control) bus, a databus...an error on the active bus, the controller...
www.cisco.com/en/US/ts/fn/000/fn2288_12231998.html
28 Dec 1998
...into the card. The following...with 9.3 switch software. BXM Model...be used to upgrade BXM cards during the upgrade...MFE is a not on Cisco...clear" state. But in...primary card active. Then...LCNs for control VC as default...Switch Software was upgraded for the particular...the current state. Now the...and back cards are present...updated. During this update...leads to a loop. Workaround...non-revertive switching with cnfapsln...happen in standby "VrmDekConnEndPoint...syncs up with active, it tries...
www.cisco.com/en/US/docs/switches/wan/bpx/release/notes/9351rn.html
14 Apr 2008
...Softswitch Control VISM supports...provides a heartbeat...are no more active calls, the card is ready for a upgrade and/or...incorporated into Software Release 1...MGX 8850 switch. The MGX...CSCds10270 When a OC-12...trying to switch APS line...CSCds10765 Software error 20304 was observed during resetsys...From Cisco WAN Manager...Secondary active card LEDS show...
www.cisco.com/en/US/docs/switches/wan/mgx/mgx_8850/software/release/notes/rn1134.html
04 Nov 2007
1.1.31 Software Release Notes Cisco WAN MGX 8850, 8230...are available in a CD-ROM package...1.31 The active PXM will be able...Far End Alarm and Control). The two main purposes...terminal. The active PXM will initiate...will run on the standby PXM also. This...service on the FRSM card. The current FRSM...Destination or Switch. Only relevant...
www.cisco.com/en/US/docs/switches/wan/mgx/mgx_8850/software/release/notes/rn1131.html
02 Nov 2007
...deploying a service...necessary, upgrade the service module software. A VSS...to contain switching module...active and VSS standby supervisor...supervisor engine controls both chassis...forwarding, and state information...between the VSS active and VSS standby...supervisor engine during initialization...rhi-routes switch num slot...routes in a service module...Mod Ports Card Type Model...Application Control Engine Module...supports a fast software upgrade (FSU...reloading the VSS standby supervisor...chassis. During the FSU procedure...between the VSS active and the VSS...on the VSS active and VSS...
References:
206
TAC
|
5
Support Community
-
View All
www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/12.2SX/configuration/guide/vss.html
25 Apr 2012
...card and a user name...switchcc y Switch the roles...active and standby cards so you can upgrade the non-upgraded card in standby...that the software versions...press Return during the reboot...prevents the active card from...both the active and standby...non-graceful upgrade. Table 12 Software Versions Reported During Non-Graceful...performing a graceful...PXM45 or AXSM card, enter the...either the active or the standby card. The switch software...
www.cisco.com/en/US/docs/switches/wan/mgx/mgx_8850/software/release/notes/rn2160a.html
03 Nov 2007
...frame to the RPM card and as such not able to do a cc. Workaround...some versions of switch only. Workaround: Upgrade the switch version...CSCdr28177 Symptoms: During a switchcc, VISM...Symptom: Both active and standby AUSM cards in a...to telnet to the active FRSM card even...
www.cisco.com/en/US/docs/switches/wan/mgx/mgx_8850/software/release/notes/rn1127.html
03 Nov 2007
|
|
|
|
