|
|
Recommended Content
Support Toolbox
|
1 - 10 of
92 results for
Configuring a Management IP Address on Catalyst 4500/4000, 5500/5000, 6500/6000, and Catalyst Fixed Configuration Switches
|
|
|
|
This document describes how to configure a management IP address on Catalyst 4500/4000, 5500/5000, and 6500/6000 series switches that run Catalyst OS (CatOS) and Cisco IOS® Software. This document...
www.cisco.com/en/US/products/hw/switches/ps708/products_tech_note09186a008010e9ca.shtml
15 Mar 2006
This document discusses the implementation of Cisco Catalyst series switches in your network, specifically the Catalyst 4500/4000, 5500/5000, and 6500/6000 platforms. Configurations and commands are discussed under the assumption that...
References:
5
TAC
www.cisco.com/en/US/products/hw/switches/ps4324/products_tech_note09186a0080094713.shtml
29 Nov 2007
This document introduces the concept of trunking between two Ethernet switches and focuses on the IEEE 802.1Q trunking standard. After a brief description of the 802.1Q trunking mechanism, the document describes the implementation on the Catalyst 4500/4000,...
www.cisco.com/en/US/products/hw/switches/ps700/products_tech_note09186a008012ecf3.shtml
26 May 2006
This document will show the basic configuration needed to set up an 802.3ad link aggregate between a Catalyst 6500/6000 (running Catalyst OS [CatOS] system software) and a Catalyst 4500/4000 switch. 802.3ad is a new specification...
References:
21
TAC
www.cisco.com/en/US/tech/tk389/tk213/technologies_configuration_example09186a0080094470.shtml
14 Dec 2005
This document offers a sample configuration and command structure for the setup of an EtherChannel link that is a trunk link between a Catalyst Layer 2 (L2) fixed configuration switch, which includes the 2950/2955/2970/2940/2900XL/3500XL switches,...
www.cisco.com/en/US/products/hw/switches/ps663/products_configuration_example09186a0080094aec.shtml
16 Nov 2007
This document provides best practices for Catalyst 6500/6000 and 4500/4000 series switches that run Cisco IOS® Software on the Supervisor Engine.
References:
18
TAC
www.cisco.com/en/US/products/hw/switches/ps708/products_white_paper09186a00801b49a4.shtml
03 Sep 2006
This document discusses the setup of an EtherChannel between a Cisco Catalyst 5500 switch and a Catalyst 6500 switch,both running Catalyst OS (CatOS). Any Catalyst 4500/4000,5500/5000,or 6500/6000 series...
www.cisco.com/en/US/tech/tk389/tk213/technologies_configuration_example09186a0080094790.shtml
16 Nov 2007
This document provides basic information on how to configure interVLAN routing on a Catalyst switch (running Catalyst OS [CatOS] system software) using an internal router (Layer 3 [L3] card/module). The term internal router refers to these L3 cards/modules...
www.cisco.com/en/US/products/hw/switches/ps700/products_tech_note09186a008015bf9a.shtml
30 Aug 2005
This document provides a sample configuration of IEEE 802.1Q (dot1q) trunking between a Cisco Catalyst 3550/3560/3750 switch that runs Cisco IOS® Software and a Catalyst 6500/6000 series switch or Catalyst 4500/4000...
www.cisco.com/en/US/products/hw/switches/ps700/products_configuration_example09186a008010f615.shtml
12 Dec 2006
This document provides basic information on how to create VLANs on Catalyst switches that run Catalyst OS (CatOS) and Cisco IOS® System Software. The sample commands for each section use one Catalyst switch from each configuration section.
References:
11
TAC
|
2
Support Community
-
View All
www.cisco.com/en/US/tech/tk389/tk689/technologies_configuration_example09186a008009478e.shtml
09 Jul 2007
|
|
|
|
