|
|
|
1 - 10 of
26,504 results for
Configuring the Call Routing Rule Function
|
|
|
|
Configuring the Call Routing Rule Function
www.cisco.com/en/US/products/ps10030/products_qanda_item09186a0080a35ebe.shtml
12 Dec 2008
A dial plan essentially describes the number and pattern of digits that a user dials to reach a particular telephone number. Access codes, area codes, specialized codes, and combinations of the number of digits dialed are all part of a dial plan. For instance, the North American...
www.cisco.com/en/US/products/sw/voicesw/ps556/products_tech_note09186a00800949f0.shtml
18 Jul 2006
Voice Translation Profiles introduce a new scheme to translate numbers. The older translation rules are to be gradually phased out of the system. Cisco strongly recommends you only use one scheme of translation rules. If you mix the old and new schemes, you can have...
References:
58
TAC
|
7
Support Community
-
View All
www.cisco.com/en/US/tech/tk652/tk90/technologies_configuration_example09186a00803f818a.shtml
02 Feb 2006
...to connect with and register to the Cisco CallManager (CCM). Messages...other IP phone users with which a call can be placed. To be able to deploy Cisco IOS NAT between the IP phone and CCM in a scalable...to the CCM and it matches the configured NAT translation rules, NAT will translate the original...
www.cisco.com/en/US/docs/ios/12_2/ip/configuration/guide/1cfipadr.html
23 May 2005
...example, you can use dialing rules to automatically prefix a digit...to an outside line. You configure application dialing rules on Cisco Unified Communications...Unified CM Administration > Call Routing > Dial Rules > Application Dial Rules. Note The Click to Call application cannot...
References:
6
TAC
www.cisco.com/en/US/docs/voice_ip_comm/cupa/click_to_call/8.0/english/install/guide/config_cucm.html
06 Jul 2010
...html#wp1040848 f. Use the Display Certificates function in the Cisco Unified Call Manager software to verify...html#wp1040354 Step 4 Configure the phone proxy instance...overlap with existing static NAT rules, and cannot be the same as...behind a router or gateway, add routes to the media termination address...
References:
9
TAC
www.cisco.com/en/US/docs/security/asa/asa80/configuration/guide/unified_comm.html
28 Apr 2008
...flag in the multicast route entry. To configure the router itself to be a statically...stopping forwarding is called the IGMP leave latency...The network manager can configure the router to stay on the shared...multicast datagrams. It functions as follows: •If a...interface list of a multicast routing table entry. •If the...
References:
6
TAC
www.cisco.com/en/US/docs/ios/12_2/ip/configuration/guide/1cfmulti.html
01 May 2003
...to make to your HTML code and the tasks required to configure the ASA to use your code. Figure...Login form is displayed by a function called by the HTML code. Figure...
References:
26
TAC
|
1
Support Community
-
View All
www.cisco.com/en/US/docs/security/asa/asa84/configuration/guide/vpn_clientless_ssl.html
14 May 2010
...about transcoding, see "Configuring Transcoding Resources". Hairpin call routing provides the following benefits: ...For information about configuring Cisco Unified CME to forward calls using local hairpin routing, see the "Forwarding Calls Using...
References:
11
TAC
|
2
Support Community
-
View All
www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmetrans.html
21 Mar 2010
...hairpinning (which means that the call comes in one voice port and is routed out another voice port). It also supports POTS-to-IP call legs and IP-to-POTS call...hairpinning. This means that the SIP gateway cannot take an...dial peers allow a user to configure the bytes parameter associated...minimum. To configure SIP functions on the Cisco AS5300, Cisco...
References:
5
TAC
www.cisco.com/en/US/docs/ios/12_2/voice/configuration/guide/vvfsip.html
09 Nov 2001
|
|
|
|
