|
|
Recommended Content
Support Toolbox
|
1 - 10 of
49 results for
How to Distinguish Between Different IGX NTM Models
|
|
|
|
...verify the IGX-NTM model. Reference...Tip called How to Distinguish Between Different IGX NTM Models for more details...
www.cisco.com/en/US/ts/fn/misc/fn981012.html
04 Apr 2005
This error applies to the IGX broadband trunk module (BTM) with T3,E3,and E1 backcards.
www.cisco.com/en/US/products/hw/modules/ps3909/products_tech_note09186a0080093d08.shtml
17 Apr 2009
This document provides common IGX configuration scenarios that are typically found in real working networks. The majority of these labs are simple,yet effective,in demonstrating the abilities of the multiservice IGX switch.
www.cisco.com/en/US/products/hw/switches/ps988/products_configuration_example09186a00801c1211.shtml
30 Apr 2009
...Negotiation for telnet between AIX and BPX CSCdm48790...in a node CSCdm69629 Different values of statistical...line alarms are not sent to SV+ CSCdp50871 UP...Clear Trap 20100 does not distinguish various types of clear...occurs when snmpwalk on an IGX node CSCdp95286 Cross...release for the UXM card on IGX. Firmware is the same...memory drivers are upgraded to support more flash memory...compatible with UXM and UXM-E model H/W all models. Previous...actual delay on the line is different. IMA trunk statistics...approximately a minute between changes. Upgrade boot...
www.cisco.com/en/US/docs/switches/wan/bpx/release/notes/9238rn.html
14 Apr 2008
...software. This feature allows users to access the IOS CLI of the URM embedded router from the IGX CLI, so that users can access the router without having to be physically connected to the...special VC used by URM for IPC between Admin Processor and IOS. When...ACTIVE URM card. Back cards of two different types can be swapped only in a...resources. These sections explain how to obtain technical information...
www.cisco.com/en/US/docs/switches/wan/bpx/release/notes/9351rn.html
14 Apr 2008
...Negotiation for telnet between AIX and BPX CSCdm48790...cards in a node CSCdm69629 Different values of statistical...line alarms are not sent to SV+ CSCdp50871 UP/Down...Clear Trap 20100 does not distinguish various types of...occurs when snmpwalk on an IGX node CSCdp95286 Cross...release for the UXM card on IGX. Firmware is the same...memory drivers are upgraded to support more flash memory...compatible with UXM and UXM-E model H/W all models. ...actual delay on the line is different. IMA trunk statistics...approximately a minute between changes. R E V I E W D...
www.cisco.com/en/US/docs/switches/wan/bpx/release/notes/9238rn.pdf
1565KB
...URM embedded router from the IGX CLI, so that users can access the router without having to be physically connected to the...OL-xxxxx-xx Appendix D—URM Model B Firmware XBC Release Notes...URM Admin firmware from XBB to XBC. Boot Code Requirements...special VC used by URM for IPC between Admin Processor and IOS. When...URM card. Back cards of two different types can be swapped only in...resources. These sections explain how to obtain technical information...
www.cisco.com/en/US/docs/switches/wan/bpx/release/notes/9351rn.pdf
1935KB
...user-supplied network name can be up to 10 characters long and should...characters (no periods). For the IGX ports, the asi_line table...feature is disabled by default. To enable the feature and...manual resync. The CWM does not distinguish between the Ethernet back card versions...
www.cisco.com/en/US/docs/net_mgmt/cisco_wan_manager/15.3.00/release/notes/15300rn.html
01 May 2006
...user-supplied network name can be up to 10 characters long and should...characters (no periods). For the IGX ports, the asi_line table...feature is disabled by default. To enable the feature and...resync. –The CWM does not distinguish between the Ethernet back card versions...
www.cisco.com/en/US/docs/net_mgmt/cisco_wan_manager/15.1.50_patch_1.0/release/notes/1515rnp1.html
03 Nov 2007
...user-supplied network name can be up to 10 characters long and should...characters (no periods). For the IGX ports, the asi_line table...feature is disabled by default. To enable the feature and...resync. –The CWM does not distinguish between the Ethernet back card versions...
www.cisco.com/en/US/docs/net_mgmt/cisco_wan_manager/15.1.50_patch_2.0/release/notes/1515rnp2.html
03 Nov 2007
|
|
|
|
