|
|
|
|
Recommended Content
Support Toolbox
|
1 - 10 of
250 results for
How to Replace a System Clock Module (SCM) on an IGX Switch
|
|
|
|
...CSCds16812 Symptom: When a cbr/ubr/vbr connection...programming value sent to the trunk card are...only happens with an asymmetrical load...Configuring APS on BPX with cnfapsln...Conditions: Switch software release prior...software does not know how to interpret the...Condition: This is due to an invalid atmEndptSCR...Symptom: Secondary clock sources are hidden...Switch Software Release IGX/BPX 9.1.19-9...not show up, the system gives a copycons failed...
www.cisco.com/en/US/docs/switches/wan/bpx/release/notes/9238rn.html
14 Apr 2008
...be useful. This is an enhancement request...The display attempts to display the port on the via trunk before...after switchcc or system rebuilt. Conditions...the addcon command to add a new PVC. The dsplogcd...1) and the loop clock were configured to...upgrading SWSW on IGX from 9.2 to 9...Y-red slot. 3. Replace the card into the...programming. 5. Switch to the standby card...
www.cisco.com/en/US/docs/switches/wan/bpx/release/notes/9351rn.html
14 Apr 2008
...ifNum> command to delete the LMI from the feeder interface. Replace <ifNum> with the number assigned to the port. Note Remove... Step 4 Establish a configuration session...For more information on the IGX switch and the IGX CLI...Preparing Service Modules for Communication This chapter describes how to prepare service modules for operation in an MGX switch. All MGX...
www.cisco.com/en/US/docs/switches/wan/mgx/software/mgx_r5.5/data/8850/configuration/5510/mgx5scg.pdf
7336KB
...ifNum> command to delete the LMI from the feeder interface. Replace <ifNum> with the number assigned to the port. Note Remove... Step 4 Establish a configuration session...For more information on the IGX switch and the IGX CLI...Preparing Service Modules for Communication This chapter describes how to prepare service modules for operation in an MGX switch. All MGX...
www.cisco.com/en/US/docs/switches/wan/mgx/mgx_8850/software/mgx_r5.4/configuration/guide/mgx54scg.pdf
7223KB
...ifNum> command to delete the LMI from the feeder interface. Replace <ifNum> with the number assigned to the port. Note Remove... Step 4 Establish a configuration session...For more information on the IGX switch and the IGX CLI...Preparing Service Modules for Communication This chapter describes how to prepare service modules for operation in an MGX switch. All MGX...
www.cisco.com/en/US/docs/switches/wan/mgx/software/mgx_r5.5/data/8850/configuration/guide/mgx5scg.pdf
7334KB
...ifNum> command to delete the LMI from the feeder interface. Replace <ifNum> with the number assigned to the port. Note...Step 4 Establish a configuration session...For more information on the IGX switch and the IGX CLI...Preparing Service Modules for Communication This chapter describes how to prepare service modules for operation in an MGX switch. All MGX...
www.cisco.com/en/US/docs/switches/wan/mgx/mgx_8850/software/mgx_r5.2/data/configuration/guide/fbmgx5scg.pdf
7068KB
...the boot system c:<IOS...memory command to save the...ready to replace an MGX-RPM-128M...be running a minimum firmware...B, the module will be put...describe how to upgrade...software on RPM cards...3 rswzen2 System Rev:03...8.PXM.a > dspcd 1...Type <CR> to continue...MGX service modules. The switchredcd command replaces the softswitch...removing an active RPM-PR...8000 series switch shelf...information on the switchredcd...Expanded Clock Source Selection...
www.cisco.com/en/US/docs/switches/wan/mgx/mgx_8850/software/release/notes/RPMPRT5.html
03 Nov 2007
...the boot system c:<IOS...memory command to save the...ready to replace an MGX-RPM-128M...be running a minimum firmware...B, the module will be put...describe how to upgrade...software on RPM cards...3 rswzen2 System Rev:03...8.PXM.a > dspcd 1...Type <CR> to continue...MGX service modules. The switchredcd command replaces the softswitch...removing an active RPM-PR...8000 series switch shelf...information on the switchredcd...Expanded Clock Source Selection...
www.cisco.com/en/US/docs/switches/wan/mgx/mgx_8850/software/release/notes/RPMPR4.html
03 Nov 2007
...the boot system c:<IOS...memory command to save the...ready to replace an MGX-RPM-128M...be running a minimum firmware...B, the module will be put...describe how to upgrade...software on RPM cards...3 rswzen2 System Rev:03...8.PXM.a > dspcd 1...Type <CR> to continue...MGX service modules. The switchredcd command replaces the softswitch...removing an active RPM-PR...8000 series switch shelf...information on the switchredcd...Expanded Clock Source Selection...
www.cisco.com/en/US/docs/switches/wan/mgx/mgx_8850/software/release/notes/RPMPR302.html
03 Nov 2007
...installation guide replaces all previous...Describes how to configure...available on the CLI of...Cisco MGX 8950 switches. Cisco ATM...cards and a command...switch requires an SES for PNNI...Processor Module (RPM-XF...the Cisco IGX 8400 Series switch. Note The...information on the general...Series Switch System Error Messages... Provides a technical...Processor Module Installation...Describes how to install and...
www.cisco.com/en/US/docs/switches/wan/mgx/mgx_8850/software/release/notes/40108x50.html
02 Nov 2007
|
|
|
|
|
