|
|
|
1 - 10 of
909 results for
Replace an In-Service ONS 15327 Chassis
|
|
|
|
This document provides guidance to replace an in-service ONS 15327 chassis that runs release 5. This document applies to all versions of ONS 15327 later than 3.2, provided you replace the linked procedures for release 5 with the relevant...
www.cisco.com/en/US/products/hw/optical/ps2001/products_tech_note09186a008069d004.shtml
05 May 2006
...facility is brought back in service. Step 1 If the...provisioned in the chassis. Step 2 If the alarm...if the card is not an XTC card). b...administrative state of any in-service (IS) ports. d...see the "Typical ONS 15327 Traffic Card LED...Before you install or replace the equipment...
www.cisco.com/en/US/docs/optical/15000r7_0/15327/troubleshooting/guide/2770alts.html
06 Feb 2012
...facility is brought back in service. Step 1 If the...provisioned in the chassis. Step 2 If the alarm...if the card is not an XTC card). b...admin state of any in-service (IS) ports. d...see the "Typical ONS 15327 Traffic Card LED...Before you install or replace the equipment...
www.cisco.com/en/US/docs/optical/15000r6_0/15327/troubleshooting/guide/2760alts.html
07 Sep 2007
...facility is brought back in service. Step 1 If the...provisioned in the chassis. Step 2 If the alarm...if the card is not an XTC cross-connect...Admin State of any in-service (IS) ports. d...see the "Typical ONS 15327 Traffic Card LED...Before you install or replace the equipment...
www.cisco.com/en/US/docs/optical/15000r5_0/15327/troubleshooting/guide/2750alts.html
26 Nov 2007
...the alarm is raised against an XTC, ensure that there is...installed and provisioned in the chassis. Step 2 If the alarm is...c. Click the State of any in-service ports. d. Choose OOS to...are looking at the physical ONS 15327, the ACT/STBY LED is on...node view of the ONS 15327, an amber LED depiction with "Sby" has replaced the white "LDG" depiction...
www.cisco.com/en/US/docs/optical/15000r4_6/15327/troubleshooting/guide/2746alts.html
30 Aug 2007
...entire assembly. You cannot replace an individual fan. The FAN STATUS...fail. For a procedure that replaces the fan tray, see the "Install...describes how to connect the ONS 15327 shelf assembly to the power supply. Terminate the chassis ground to either the office...
www.cisco.com/en/US/products/hw/optical/ps2001/products_installation_and_configuration_guide_chapter09186a0080176f3e.html
09 Jan 2006
...that the correct port is in service. Step 3 Use a test...there is a valid signal, replace the DS-N connector on the ONS 15327. Step 6 Repeat Steps...you replace a card with an identical type of card...that the proper ports are in service. Step 4 Use an optical test set to verify...connected properly. Step 7 Replace the OC-N card. ...SSM) received by the ONS 15327 failed. The problem is...
www.cisco.com/en/US/products/hw/optical/ps2001/products_installation_and_configuration_guide_chapter09186a0080952bc7.html
25 Feb 2008
...If there is a valid signal, replace the DS-1 or DS-3 connector on the ONS 15327. Step 6 Try another port...source of the problem. Step 8 Replace the reporting card: (a...When you replace a card with an identical type of card, you...when the port on the card is in-service but no signal is being received...
www.cisco.com/en/US/products/hw/optical/ps2001/products_installation_and_configuration_guide_chapter09186a0080176f38.html
09 Jan 2006
...the alarm is raised against an XTC, ensure that there is...installed and provisioned in the chassis. Step 2 If the alarm is...c. Click the State of any in-service ports. d. Choose OOS to...are looking at the physical ONS 15327, the ACT/STBY LED is illuminated...node view of the ONS 15327, an amber LED depiction with "Sby" has replaced the white "LDG" depiction...
www.cisco.com/en/US/docs/optical/15000r4_1/15327/troubleshooting/guide/2741alts.html
28 Aug 2007
...As of Release 3.3 the ONS 15327 is supported for acting as an intermediate node in Orderwire...Buildout (LBO) distance for the ONS 15327 BITS out signal. This setting...3. In Release 3.3, in-service span upgrades are supported...higher-rate optical card must replace the lower-rate card in the...
www.cisco.com/en/US/products/hw/optical/ps2001/prod_release_note09186a0080952c83.html
25 Feb 2008
|
|
|
|
