|
|
|
1 - 10 of
6,094 results for
Use PAT to Establish a
|
|
|
|
This document provides a sample configuration for Port Address Translation (PAT) to establish a session between Cisco Transport Controller (CTC) and ONS 15454 when CTC resides inside the firewall.
www.cisco.com/en/US/products/hw/optical/ps2006/products_configuration_example09186a00804ade6b.shtml
12 Jan 2006
...Firewall for Routing •Establishing Outbound Connectivity with NAT and PAT •Testing Connectivity...Configuration Examples •Using Outside NAT •Enabling...This section describes how to set default routes on devices...Route for Network Hosts A router discovers and stores...Address Translation (PAT) to establish outbound connectivity from...higher security interfaces to hosts on lower security interfaces...Overview •How NAT and PAT Work •Configuring NAT...Controlling Network Access and Use." Static NAT provides a permanent one-to-one map...
www.cisco.com/en/US/docs/security/pix/pix62/configuration/guide/bafwcfg.html
04 May 2007
Microsoft (MS) Point-to-Point Tunneling Protocol (PPTP) is used to enable remote users to connect back to their corporate network in a secured manner across the public Internet. You can allocate a single IP address to a remote location to...
www.cisco.com/en/US/tech/tk827/tk369/technologies_configuration_example09186a00800949c0.shtml
19 Oct 2006
This document shows how to configure a Network Address Translation Traversal (NAT-T) between Cisco VPN Clients located behind a Port Address Translation (PAT)/NAT device and a remote Cisco VPN Concentrator. NAT-T can be used between VPN Clients and a VPN...
www.cisco.com/en/US/products/sw/secursw/ps2308/products_configuration_example09186a008010edf4.shtml
04 May 2004
This sample configuration shows how to set up multiple VPN Group Clients to use different VLANs after the IPsec tunnel is established with the PIX 500 Series Security Appliance.
www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a00806ab788.shtml
02 Oct 2009
This document provides a sample configuration for how to enable the PIX/ASA Security Appliance to accept dynamic IPsec connections from the IOS® router. In this scenario, the IPSec tunnel establishes when the tunnel is initiated from the Router end only. ASA could not initiate...
References:
19
TAC
|
3
Support Community
-
View All
www.cisco.com/en/US/products/ps6120/products_configuration_example09186a0080b3d511.shtml
28 Jul 2010
This document provides troubleshooting tips you can use in order to resolve connectivity issues with the Cisco VPN 3000 Concentrator.
www.cisco.com/en/US/products/hw/vpndevc/ps2284/products_tech_note09186a0080094eca.shtml
30 Nov 2006
...Replace security_level with a value such as security40 or security60...security level between 1 and 99 for a perimeter interface. This section describes how to use Network Address Translation (NAT) and Port Address Translation (PAT) to establish outbound connectivity from hosts...
www.cisco.com/en/US/docs/security/pix/pix63/configuration/guide/bafwcfg.html
16 Nov 2007
...reliably initiate a connection to a host that uses dynamic PAT (even if the connection is allowed...reliable access to hosts. Dynamic PAT allows you to use a single global address, which helps...
www.cisco.com/en/US/docs/interfaces_modules/services_modules/ace/v3.00_A2/configuration/security/guide/nat.html
09 Apr 2009
...Pool 1, the same address is used to satisfy subsequent requests, and PAT is used to distinguish between the hosts using the address. A previously configured NAT rule will...
www.cisco.com/en/US/docs/routers/access/cisco_router_and_security_device_manager/24/software/user/guide/Morabout.html
09 Apr 2007
|
|
|
|
