|
|
|
|
Recommended Content
Support Toolbox
|
1 - 10 of
20 results for
Why Is the ip ospf interface-retry 0 Configuration Command Added to All Interfaces
|
|
|
|
...the level for IS-IS. The range is from 1 to 2. level level (Optional) Specifies that the LSP cannot be reoptimized...Limits CSPF to a single OSPF instance and area. ospf...OSPF area ID. value IP address for the OSPF area...verbatim Cisco IOS XR MPLS Command Reference for the Cisco CRS Router, Release 4.0 OL-23221-02 297 ...Command Modes Tunnel-te interface configuration Command History Modification...protecting keyword was added to support GMPLS protection...
www.cisco.com/en/US/docs/routers/crs/software/crs_r4.0/mpls/command/reference/b_gr40crs1book.pdf
5756KB
...information. Internet Protocol (IP) Messages IPV6_ND Messages...Reference Guide, Release 4.0 OL-24133-01 IPV6_ND Messages Error Message %IP-IPV6_ND-3-ADDRESS...been detected. This error is caused by a mis-configuration. More than one system, connected to the same media, are configured...Local address, then the ipv6 interface is also taken to DOWN state...occurred while attempting to add/delete an adjacency into...neighbor [location node-id] commands. Entries in AIB should match...
www.cisco.com/en/US/docs/ios_xr_sw/iosxr_r4.0.1/error/messages/em401sems.pdf
24416KB
...the level for IS-IS. The range is from 1 to 2. level level (Optional) Specifies that the LSP cannot be reoptimized...Limits CSPF to a single OSPF instance and area. ospf...OSPF area ID. value IP address for the OSPF area...verbatim Cisco IOS XR MPLS Command Reference for the Cisco...Command Modes Tunnel-te interface configuration Command History Modification...introduced. Release 2.0 The protecting keyword was added to support GMPLS protection...
www.cisco.com/en/US/docs/routers/crs/software/crs_r4.1/mpls/command/reference/b_mpls_cr41crs.pdf
6030KB
...Installation related messages. IP All Internet Protocol (IP) related messages. L1 All...Error Messages Overview How to Read System Messages EM-3...severity levels correspond to the keywords assigned by the logging...and logging monitor global configuration commands that define where and at what...In general, the default is to log messages from level 0 (emergencies) to level 7...related messages, such as MPLS, OSPF, BGP, Multicast, MRIB...
www.cisco.com/en/US/docs/ios_xr_sw/iosxr_r4.2/error/messages/em42.pdf
21339KB
...Installation related messages. IP All Internet Protocol (IP) related messages. L1 All...Error Messages Overview How to Read System Messages EM-5...severity levels correspond to the keywords assigned by the logging...and logging monitor global configuration commands that define where and at what...In general, the default is to log messages from level 0 (emergencies) to level 7...related messages, such as MPLS, OSPF, BGP, Multicast, MRIB...
www.cisco.com/en/US/docs/ios_xr_sw/iosxr_r4.3/error/messages/em43x.pdf
18978KB
...the level for IS-IS. The range is from 1 to 2. level level (Optional) Specifies that the LSP cannot be reoptimized...Limits CSPF to a single OSPF instance and area. ospf...value Cisco IOS XR MPLS Command Reference for the Cisco...path-option (MPLS-TE) IP address for the OSPF area...Command Modes Tunnel-te interface configuration Command History Modification...introduced. Release 2.0 The protecting keyword was added to support GMPLS protection...
www.cisco.com/en/US/docs/routers/crs/software/crs_r4.2/mpls/command/reference/b_mpls_cr42crs.pdf
6144KB
...conditions warrant, upgrade to a larger memory configuration. If resource allocation was not the problem and it hasn’t been...information. Internet Protocol (IP) Messages IPV4_MA Messages...Message %IP-IPV4_MA-3-ADD_GROUP_FAILED IP add multicast...failed for group [chars] on interface CH[hex] Explanation IPv4 was unable to add membership to the group. Commonly, this is done for 224.0.0.1 by ipv4-ma with no...
www.cisco.com/en/US/docs/ios_xr_sw/iosxr_r4.1/error/messages/em41sems.pdf
17387KB
...Workaround: There is no workaround...Path First (OSPF) as IGP configured, the standby RP...failure due to Servicing...mismatched commands via: show...MCL file: interface Tunnel3000...interface" - ip ospf interface-retry 0 ! </submode...Conditions: The symptom will...in a mis-configuration where the...H323-H323 is configured...
www.cisco.com/en/US/docs/ios/12_4t/release/notes/124TCAVS2.html
19 Sep 2012
...Workaround: There is no workaround...Path First (OSPF) as IGP configured, the standby RP...failure due to Servicing...mismatched commands via: show...MCL file: interface Tunnel3000...interface" - ip ospf interface-retry 0 ! </submode...Conditions: The symptom will...in a mis-configuration where the...H323-H323 is configured...
www.cisco.com/en/US/docs/ios/12_4t/release/notes/124TCAVS2.pdf
1661KB
...Both the isis keyword and the ospf keyword were added. Release 3.8.0 The pce, address, and ipv4...MPLS Traffic Engineering Commands on Cisco IOS XR Software...following example shows how to limit CSPF to a single IS-IS instance and area...CPU0:router(config)# interface tunnel-te 1 RP/0...Displays the configured IP explicit paths. show mpls...overload command in MPLS-TE configuration mode. To return to the...
www.cisco.com/en/US/docs/ios_xr_sw/iosxr_r3.8/mpls/command/reference/gr38book.pdf
3234KB
|
|
|
|
|
