Applied Mitigation Bulletin

Contents

This Applied Mitigation Bulletin is a companion document to the PSIRT Security Advisory Portable SDK for UPnP Devices Contains Buffer Overflow Vulnerabilities and provides identification and mitigation techniques that administrators can deploy on Cisco network devices.

Vulnerability Characteristics

The Intel uPNP SDK and the portable SDK for UPnP™ Devices (libupnp) are affected by multiple vulnerabilities when processing Simple Service Discovery Protocol (SSDP) requests over IP version 4 (IPv4) and IP version 6 (IPv6). This vulnerability can be exploited remotely without authentication and without end-user interaction. Successful exploitation of this vulnerability could allow arbitrary code execution. The attack vector for exploitation is through SSDP IPv4 and IPv6 packets using UDP port 1900. An attacker could exploit this vulnerability using spoofed packets.

This vulnerability has been assigned Common Vulnerabilities and Exposures (CVE) identifiers CVE-2012-5958, CVE-2012-5959, CVE-2012-5960, CVE-2012-5961, CVE-2012-5962, CVE-2012-5963, CVE-2012-5964, and CVE-2012-5965.

Vulnerability Overview

Information about vulnerable, unaffected, and fixed software is available in the Cisco Security Advisory, which is available at the following link: http://tools.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20130129-upnp

Mitigation Technique Overview

Cisco devices provide several countermeasures for these vulnerabilities. Administrators are advised to consider these protection methods to be general security best practices for infrastructure devices and the traffic that transits the network. This section of the document provides an overview of these techniques.

Cisco IOS Software can provide effective means of exploit prevention using the following methods:

• Infrastructure access control lists (iACLs)
• Unicast Reverse Path Forwarding (uRPF)
• IP source guard (IPSG)

These protection mechanisms filter and drop, as well as verify the source IP address of, packets that are attempting to exploit these vulnerabilities.

The proper deployment and configuration of uRPF provides an effective means of protection against attacks that use packets with spoofed source IP addresses. uRPF should be deployed as close to all traffic sources as possible.

The proper deployment and configuration of IPSG provides an effective means of protection against spoofing attacks at the access layer.

Effective means of exploit prevention can also be provided by the Cisco ASA 5500 Series Adaptive Security Appliance, Cisco Catalyst 6500 Series ASA Services Module (ASASM), and the Firewall Services Module (FWSM) for Cisco Catalyst 6500 Series Switches and Cisco 7600 Series Routers using the following:

• Transit access control lists (tACLs)
• Unicast Reverse Path Forwarding (uRPF)

These protection mechanisms filter and drop, as well as verify the source IP address of, packets that are attempting to exploit these vulnerabilities.

Cisco IOS NetFlow records can provide visibility into network-based exploitation attempts.

Cisco IOS Software, Cisco ASA, Cisco ASASM, and Cisco FWSM firewalls can provide visibility through syslog messages and counter values displayed in the output from show commands.

Effective use of Cisco Intrusion Prevention System (IPS) event actions provides visibility into and protection against attacks that attempt to exploit these vulnerabilities.

The Cisco Security Manager can also provide visibility through incidents, queries, and event reporting.

Risk Management

Organizations are advised to follow their standard risk evaluation and mitigation processes to determine the potential impact of these vulnerabilities. Triage refers to sorting projects and prioritizing efforts that are most likely to be successful. Cisco has provided documents that can help organizations develop a risk-based triage capability for their information security teams. Risk Triage for Security Vulnerability Announcements and Risk Triage and Prototyping can help organizations develop repeatable security evaluation and response processes.

Caution:The effectiveness of any mitigation technique depends on specific customer situations such as product mix, network topology, traffic behavior, and organizational mission. As with any configuration change, evaluate the impact of this configuration prior to applying the change.

Specific information about mitigation and identification is available for these devices:

• Cisco IOS Routers and Switches
• Cisco IOS NetFlow and Cisco IOS Flexible NetFlow
• Cisco ASA, Cisco ASASM, and Cisco FWSM Firewalls
• Cisco Intrusion Prevention System
• Cisco Security Manager

Cisco IOS Routers and Switches

Mitigation: Infrastructure Access Control Lists

To protect infrastructure devices and minimize the risk, impact, and effectiveness of direct infrastructure attacks, administrators are advised to deploy infrastructure access control lists (iACLs) to perform policy enforcement of traffic sent to infrastructure equipment. Administrators can construct an iACL by explicitly permitting only authorized traffic sent to infrastructure devices in accordance with existing security policies and configurations. For the maximum protection of infrastructure devices, deployed iACLs should be applied in the ingress direction on all interfaces to which an IP address has been configured. An iACL workaround cannot provide complete protection against these vulnerabilities when the attack originates from a trusted source address.

The iACL policy denies unauthorized SSDP packets on UDP port 1900 that are sent to affected devices. In the following example, 192.168.60.0/24 and 2001:DB8:1:60::/64 represent the IP address space that is used by the affected devices, and the hosts at 192.168.100.1 and 2001:DB8::100:1 are considered trusted sources that require access to the affected devices. Care should be taken to allow required traffic for routing and administrative access prior to denying all unauthorized traffic. Whenever possible, infrastructure address space should be distinct from the address space used for user and services segments. Using this addressing methodology will assist with the construction and deployment of iACLs.

Additional information about iACLs is in Protecting Your Core: Infrastructure Protection Access Control Lists.

ip access-list extended Infrastructure-ACL-Policy
  !
  !-- Include explicit permit statements for trusted sources
  !-- that require access on the vulnerable protocols and ports
  !
  permit udp host 192.168.100.1 192.168.60.0 0.0.0.255 eq 1900
  permit udp host 192.168.100.1 host 239.255.255.250 eq 1900
  !
  !-- The following vulnerability-specific access control entries
  !-- (ACEs) can aid in identification of attacks
  !
  deny udp any 192.168.60.0 0.0.0.255 eq 1900
  !
  !-- Explicit deny ACE for traffic sent to addresses configured within
  !-- the infrastructure address space
  !
  deny ip any 192.168.60.0 0.0.0.255  
  !
  !-- Permit or deny all other Layer 3 and Layer 4 traffic in accordance
  !-- with existing security policies and configurations
  !
!
!-- Create the corresponding IPv6 iACL 
!
ipv6  access-list IPv6-Infrastructure-ACL-Policy
  !
  !-- Include explicit permit statements for trusted sources
  !-- that require access on the vulnerable protocols and ports
  !
  permit udp host 2001:DB8::100:1 2001:DB8:1:60::/64 eq 1900
  permit udp host 2001:DB8::100:1 FF02:0:0:0:0:0:0:C eq 1900
  permit udp host 2001:DB8::100:1 FF05:0:0:0:0:0:0:C eq 1900   
  permit udp host 2001:DB8::100:1 FF08:0:0:0:0:0:0:C eq 1900  
  permit udp host 2001:DB8::100:1 FF0E:0:0:0:0:0:0:C eq 1900 
  !
  !-- The following vulnerability-specific access control entries
  !-- (ACEs) can aid in identification of attacks to global and
  !-- link-local addresses
  !
  deny udp any 2001:DB8:1:60::/64 eq 1900
  !
  !-- Permit other required traffic to the infrastructure address
  !-- range and allow IPv6 neighbor discovery packets, which
  !-- include neighbor solicitation packets and neighbor
  !-- advertisement packets
  !
  permit icmp any any nd-ns
  permit icmp any any nd-na
  ! 
  !--  Explicit deny for all other IPv6 traffic to the global
  !--  infrastructure address range
  !
  deny ipv6 any 2001:DB8:1:60::/64
  !
  !--  Permit or deny all other Layer 3 and Layer 4 traffic
  !--  in accordance with existing security policies and configurations
  !  
  !-- Apply iACLs to interfaces in the ingress direction 
  !
interface GigabitEthernet0/0
 ip access-group Infrastructure-ACL-Policy in
 ipv6 traffic-filter IPv6-Infrastructure-ACL-Policy in

Note that filtering with an interface access list will elicit the transmission of ICMP unreachable messages back to the source of the filtered traffic. Generating these messages could have the undesired effect of increasing CPU utilization on the device. In Cisco IOS Software, ICMP unreachable generation is limited to one packet every 500 milliseconds by default. ICMP unreachable message generation can be disabled using the interface configuration commands no ip unreachables and no ipv6 unreachables. ICMP unreachable rate limiting can be changed from the default using the global configuration command ip icmp rate-limit unreachable interval-in-ms and ipv6 icmp error-interval interval-in-ms.

Identification: Infrastructure Access Control Lists

After the administrator applies the iACL to an interface, the show ip access-lists and show ipv6 access-list commands will identify the number of SSDP packets on UDP port 1900 that have been filtered on interfaces on which the iACL is applied. Administrators should investigate filtered packets to determine whether they are attempts to exploit these vulnerabilities. Example output for show ip access-lists Infrastructure-ACL-Policy and show ipv6 access-list IPv6-Infrastructure-ACL-Policy follows:

router#show ip access-lists Infrastructure-ACL-Policy
Extended IP access list Infrastructure-ACL-Policy
    10 permit udp host 192.168.100.1 192.168.60.0 0.0.0.255 eq 1900 (60 matches)
    20 permit udp host 192.168.100.1 host 239.255.255.250 eq 1900  (60 matches)
    30 deny udp any 192.168.60.0 0.0.0.255 eq 1900 (9 matches)
    40 deny ip any 192.168.60.0 0.0.0.255 (17 matches)
router#

In the preceding example, access list Infrastructure-ACL-Policy has dropped 9 SSDP packets on UDP port 1900 for access control list entry (ACE) line 20.

router#show ipv6 access-list IPv6-Infrastructure-ACL-Policy 
IPv6 access list IPv6-Infrastructure-ACL-Policy
    permit udp host 2001:DB8::100:1 2001:DB8:1:60::/64 eq 1900 (71 matches) sequence 10
    permit udp host 2001:DB8::100:1 FF02:0:0:0:0:0:0:C eq 1900 (12 matches) sequence 20
    permit udp host 2001:DB8::100:1 FF05:0:0:0:0:0:0:C eq 1900 (15 matches) sequence 30
    permit udp host 2001:DB8::100:1 FF08:0:0:0:0:0:0:C eq 1900 (17 matches) sequence 40
    permit udp host 2001:DB8::100:1 FF0E:0:0:0:0:0:0:C eq 1900 (11 matches) sequence 50
    deny udp any 2001:DB8:1:60::/64 eq 1900 (58 matches) sequence 60
    permit icmp any any nd-ns (80 matches) sequence 70
    permit icmp any any nd-na (80 matches) sequence 80
    deny ipv6 any 2001:DB8:1:60::/64 (5 matches) sequence 90

In the preceding example, access list IPv6-Infrastructure-ACL-Policy has dropped 58 SSDP packets on UDP port 1900 for access control list entry (ACE) line 20.

For additional information about investigating incidents using ACE counters and syslog events, reference the Identifying Incidents Using Firewall and IOS Router Syslog Events Cisco Security Intelligence Operations white paper.

Administrators can use Embedded Event Manager to provide instrumentation when specific conditions are met, such as ACE counter hits. The Cisco Security Intelligence Operations white paper Embedded Event Manager in a Security Context provides additional details about how to use this feature.

Identification: Access List Logging

The log and log-input access control list (ACL) option will cause packets that match specific ACEs to be logged. The log-input option enables logging of the ingress interface in addition to the packet source and destination IP addresses and ports.

Caution: Access control list logging can be very CPU intensive and must be used with extreme caution. Factors that drive the CPU impact of ACL logging are log generation, log transmission, and process switching to forward packets that match log-enabled ACEs.

For Cisco IOS Software, the ip access-list logging interval interval-in-ms command can limit the effects of process switching induced by IPv4 ACL logging. The logging rate-limit rate-per-second [except loglevel] command limits the impact of log generation and transmission.

The CPU impact from ACL logging can be addressed in hardware on the Cisco Catalyst 6500 Series Switches and Cisco 7600 Series Routers with Supervisor Engine 720 or Supervisor Engine 32 using optimized ACL logging.

For additional information about the configuration and use of ACL logging, reference the Understanding Access Control List Logging Cisco Security Intelligence Operations white paper.

Mitigation: Spoofing Protection

Mitigation: Spoofing Protection Using Unicast Reverse Path Forwarding

The vulnerabilities that are described in this document can be exploited by spoofed IP packets. Administrators can deploy and configure Unicast Reverse Path Forwarding (uRPF) as a protection mechanism against spoofing.

uRPF is configured at the interface level and can detect and drop packets that lack a verifiable source IP address. Administrators should not rely on uRPF to provide complete spoofing protection because spoofed packets may enter the network through a uRPF-enabled interface if an appropriate return route to the source IP address exists. Administrators are advised to take care to ensure that the appropriate uRPF mode (loose or strict) is configured during the deployment of this feature because it can drop legitimate traffic that is transiting the network. In an enterprise environment, uRPF may be enabled at the Internet edge and the internal access layer on the user-supporting Layer 3 interfaces.

Additional information is in the Unicast Reverse Path Forwarding Loose Mode Feature Guide.

For additional information about the configuration and use of uRPF, reference the Understanding Unicast Reverse Path Forwarding Cisco Security Intelligence Operations white paper.

Mitigation: Spoofing Protection Using IP Source Guard

IP source guard (IPSG) is a security feature that restricts IP traffic on nonrouted, Layer 2 interfaces by filtering packets based on the DHCP snooping binding database and manually configured IP source bindings. Administrators can use IPSG to prevent attacks from an attacker who attempts to spoof packets by forging the source IP address and/or the MAC address. When properly deployed and configured, IPSG coupled with strict mode uRPF provides the most effective means of spoofing protection for the vulnerabilities that are described in this document.

Additional information about the deployment and configuration of IPSG is in Configuring DHCP Features and IP Source Guard.

Identification: Spoofing Protection Using Unicast Reverse Path Forwarding

With uRPF properly deployed and configured throughout the network infrastructure, administrators can use the show cef interface type slot/port internal, show ip interface, show cef drop, show ip cef switching statistics feature, and show ip traffic commands to identify the number of packets that uRPF has dropped.

Note: Beginning with Cisco IOS Software Release 12.4(20)T, the command show ip cef switching has been replaced by show ip cef switching statistics feature.

Note: The show command | begin regex and show command | include regex command modifiers are used in the following examples to minimize the amount of output that administrators will need to parse to view the desired information. Additional information about command modifiers is in the show command sections of the Cisco IOS Configuration Fundamentals Command Reference.

router#show cef interface GigabitEthernet 0/0 internal | include drop
  ip verify: via=rx (allow default), acl=0, drop=18, sdrop=0
  IPv6 unicast RPF: via=rx acl=None, drop=10, sdrop=0
router#

Note: show cef interface type slot/port internal is a hidden command that must be fully entered at the command-line interface. Command completion is not available for it.

router#show cef drop
CEF Drop Statistics
Slot  Encap_fail  Unresolved Unsupported    No_route      No_adj  ChkSum_Err
RP            27           0           0          18           0           0
router#

router#show ip interface GigabitEthernet 0/0 | begin verify

  IP verify source reachable-via RX, allow default, allow self-ping
  18 verification drops
  0 suppressed verification drops
router#
router#show ipv6 interface GigabitEthernet 0/0 | section IPv6 verify

  IPv6 verify source reachable-via rx 
  0 verification drop(s) (process), 10 (CEF)
  0 suppressed verification drop(s) (process), 0 (CEF)
  --      CLI Output Truncated       --  
router#

router#show ip cef switching statistics feature

IPv4 CEF input features:
Path   Feature                Drop    Consume       Punt  Punt2Host Gave route
RP PAS uRPF                     18          0          0          0          0
Total                           18          0          0          0          0
    --      CLI Output Truncated       --  
router#
router#show ipv6 cef switching statistics feature

IPv6 CEF input features:
Feature                       Drop   Consume   Punt   Punt2Host   Gave route
RP LES Verify Unicast R         10         0      0           0            0
Total                           10         0      0           0            0
    --      CLI Output Truncated       --  
router#

router#show ip traffic | include RPF
         18 no route, 18 unicast RPF, 0 forced drop
router#
router#show ipv6 traffic | include RPF
         10 RPF drops, 0 RPF suppressed, 0 forced drop
router#

In the preceding show cef interface type slot/port internal, show cef drop, show ip interface type slot/port and show ipv6 interface type slot/port, show ip cef switching statistics feature and show ipv6 cef switching statistics feature, and show ip traffic and show ipv6 traffic examples, uRPF has dropped the following packets received globally on all interfaces with uRPF configured because of the inability to verify the source address of the IP packets within the forwarding information base of Cisco Express Forwarding.

• 18 IPv4 packets
• 10 IPv6 packets

Cisco IOS NetFlow and Cisco IOS Flexible NetFlow

Identification: IPv4 Traffic Flow Identification Using Cisco IOS NetFlow

Administrators can configure Cisco IOS NetFlow on Cisco IOS routers and switches to aid in the identification of IPv4 traffic flows that may be attempts to exploit these vulnerabilities. Administrators are advised to investigate flows to determine whether they are attempts to exploit these vulnerabilities or whether they are legitimate traffic flows.

router#show ip cache flow
IP packet size distribution (90784136 total packets):
   1-32   64   96  128  160  192  224  256  288  320  352  384  416  448  480
   .000 .698 .011 .001 .004 .005 .000 .004 .000 .000 .003 .000 .000 .000 .000

    512  544  576 1024 1536 2048 2560 3072 3584 4096 4608
   .000 .001 .256 .000 .010 .000 .000 .000 .000 .000 .000

IP Flow Switching Cache, 4456704 bytes
  1885 active, 63651 inactive, 59960004 added
  129803821 ager polls, 0 flow alloc failures
  Active flows timeout in 30 minutes
  Inactive flows timeout in 15 seconds
IP Sub Flow Cache, 402056 bytes
  0 active, 16384 inactive, 0 added, 0 added to flow
  0 alloc failures, 0 force free
  1 chunk, 1 chunk added
  last clearing of statistics never
Protocol         Total    Flows   Packets Bytes  Packets Active(Sec) Idle(Sec)
--------         Flows     /Sec     /Flow  /Pkt     /Sec     /Flow     /Flow
TCP-Telnet    11393421      2.8         1    48      3.1       0.0       1.4
TCP-FTP            236      0.0        12    66      0.0       1.8       4.8
TCP-FTPD            21      0.0     13726  1294      0.0      18.4       4.1
TCP-WWW          22282      0.0        21  1020      0.1       4.1       7.3
TCP-X              719      0.0         1    40      0.0       0.0       1.3
TCP-BGP              1      0.0         1    40      0.0       0.0      15.0
TCP-Frag         70399      0.0         1   688      0.0       0.0      22.7
TCP-other     47861004     11.8         1   211     18.9       0.0       1.3
UDP-DNS            582      0.0         4    73      0.0       3.4      15.4
UDP-NTP         287252      0.0         1    76      0.0       0.0      15.5
UDP-other       310347      0.0         2   230      0.1       0.6      15.9
ICMP             11674      0.0         3    61      0.0      19.8      15.5
IPv6INIP            15      0.0         1  1132      0.0       0.0      15.4
GRE                  4      0.0         1    48      0.0       0.0      15.3 
Total:        59957957     14.8         1   196     22.5       0.0       1.5

SrcIf         SrcIPaddress    DstIf         DstIPaddress    Pr SrcP DstP  Pkts
Gi0/0         192.168.10.201  Gi0/1         192.168.60.102  11 0984 076C     1
Gi0/0         192.168.11.54   Gi0/1         192.168.60.158  11 0911 076C     3
Gi0/1         192.168.150.60  Gi0/0         10.89.16.226    06 0016 12CA     1
Gi0/0         192.168.60.97   Gi0/1         192.168.60.28   11 0B3E 076C     5
Gi0/0         192.168.60.17   Gi0/1         192.168.60.97   11 0B89 076C     1
Gi0/0         10.88.226.1     Gi0/1         192.168.202.22  11 007B 007B     1
Gi0/0         192.168.12.185  Gi0/1         192.168.60.239  11 0BD7 076C     1
Gi0/0         10.89.16.226    Gi0/1         192.168.150.60  06 12CA 0016     1
router#

In the preceding example, there are multiple flows for SSDP on UDP port 1900 (hex value 076C).

This traffic is sourced from and sent to addresses within the 192.168.60.0/24 address block, which is used by affected devices. The packets in these flows may be spoofed and may indicate an attempt to exploit these vulnerabilities. Administrators are advised to compare these flows to baseline utilization for SSDP traffic sent on UDP port 1900 and also investigate the flows to determine whether they are sourced from untrusted hosts or networks.

As shown in the following example, to view only the SSDP packets on UDP port 1900 (hex value 076C), use the show ip cache flow | include SrcIf|_11_.*076C command to display the related Cisco NetFlow records:

router#show ip cache flow | include SrcIf|_11_.*076C
SrcIf         SrcIPaddress     DstIf         DstIPaddress    Pr SrcP DstP  Pkts
Gi0/0         192.168.12.110   Gi0/1         192.168.60.163  11 092A 076C     6
Gi0/0         192.168.60.230   Gi0/1         192.168.60.20   11 0C09 076C     1
Gi0/0         192.168.11.131   Gi0/1         192.168.60.245  11 0B66 076C    18
Gi0/0         192.168.60.7     Gi0/1         192.168.60.162  11 0914 076C     1
Gi0/0         192.168.41.86    Gi0/1         192.168.60.27   11 0B7B 076C     2
router#

Identification: IPv6 Traffic Flow Identification Using Cisco IOS NetFlow

Administrators can configure Cisco IOS NetFlow on Cisco IOS routers and switches to aid in the identification of IPv6 traffic flows that may be attempts to exploit the vulnerabilities that are described in this document. Administrators are advised to investigate flows to determine whether they are attempts to exploit these vulnerabilities or whether they are legitimate traffic flows.

The following output is from a Cisco IOS device running Cisco IOS Software 12.4 mainline train. The command syntax will vary for different Cisco IOS Software trains.

router#show ipv6 flow cache

IP packet size distribution (50078919 total packets):
   1-32  64   96  128  160  192  224  256  288  320  352  384  416  448  480
   .000 .990 .001 .008 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000

    512  544  576 1024 1536 2048 2560 3072 3584 4096 4608
   .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000

IP Flow Switching Cache, 475168 bytes
  8 active, 4088 inactive, 6160 added
  1092984 ager polls, 0 flow alloc failures
  Active flows timeout in 30 minutes
  Inactive flows timeout in 15 seconds

IP Sub Flow Cache, 33928 bytes
  16 active, 1008 inactive, 12320 added, 6160 added to flow
  0 alloc failures, 0 force free
  1 chunk, 1 chunk added

SrcAddress        InpIf    DstAddress       OutIf    Prot SrcPrt DstPrt Packets
2001:DB...128::201 Gi0/0    2001:DB...128::20 Local    0x11 0x16C4 0x076C 1464
2001:DB...6A:5BA6 Gi0/0    2001:DB...28::21 Gi0/1    0x3A 0x0000 0x8000 1191
2001:DB...6A:5BA6 Gi0/0    2001:DB...134::3 Gi0/1    0x3A 0x0000 0x8000 1191
2001:DB...6A:5BA6 Gi0/0    2001:DB...128::4 Gi0/1    0x3A 0x0000 0x8000 1192    
2001:DB...06::201 Gi0/0    2001:DB...128::3 Gi0/1    0x11 0x1610 0x076C 1001  
2001:DB...128::201 Gi0/0    2001:DB...128::4 Gi0/1    0x11 0x1634 0x076C 1292  
2001:DB...6A:5BA6 Gi0/0    2001:DB...128::3 Gi0/1    0x3A 0x0000 0x8000 1155
2001:DB...6A:5BA6 Gi0/0    2001:DB...146::3 Gi0/1    0x3A 0x0000 0x8000 1092
2001:DB...6A:5BA6 Gi0/0    2001:DB...144::4 Gi0/1    0x3A 0x0000 0x8000 1193 

To permit display of the full 128-bit IPv6 address, use the terminal width 132 exec mode command.

In the preceding example, there are multiple IPv6 flows for SSDP on UDP port 1900 (hex value 076C).

The SSDP packets on UDP port 1900 are sourced from and sent to addresses within the 2001:DB8:1:60::/64 address block that is used by affected devices. The packets in the UDP flows may be spoofed and could indicate an attempt to exploit these vulnerabilities. Administrators are advised to compare these flows to baseline utilization for SSDP traffic on UDP port 1900 and also investigate the flows to determine whether they are sourced from untrusted hosts or networks.

As shown in the following example, to view only the SSDP packets on UDP port 1900 (hex value 076C), use the show ipv6 flow cache | include SrcIf|_11_.*076C command to display the related Cisco NetFlow records:

UDP Flows

router#show ip cache flow | include SrcIf|_11_.*076C
SrcAddress        InpIf    DstAddress       OutIf    Prot SrcPrt DstPrt Packets
2001:DB...06::201 Gi0/0    2001:DB...28::20 Local    0x11 0x16C4 0x076C 3 
2001:DB...06::201 Gi0/0    2001:DB...128::3 Gi0/1    0x11 0x1610 0x076C 11 
2001:DB...06::201 Gi0/0    2001:DB...128::4 Gi0/1    0x11 0x1634 0x076C 8
router#

Identification: IPv4 Traffic Flow Identification Using Cisco Flexible NetFlow

Introduced in Cisco IOS Software Releases 12.2(31)SB2 and 12.4(9)T, Cisco IOS Flexible NetFlow improves original Cisco NetFlow by adding the capability to customize the traffic analysis parameters for the administrator''s specific requirements. Original Cisco NetFlow uses a fixed seven tuples of IP information to identify a flow, whereas Cisco IOS Flexible NetFlow allows the flow to be user defined. It facilitates the creation of more complex configurations for traffic analysis and data export by using reusable configuration components.

The following example output is from a Cisco IOS device that is running a version of Cisco IOS Software in the 15.1T train. Although the syntax will be almost identical for the 12.4T and 15.0 trains, it may vary slightly depending on the actual Cisco IOS release being used. In the following configuration, Cisco IOS Flexible NetFlow will collect information on interface GigabitEthernet0/0 for incoming IPv4 flows based on source IPv4 address, as defined by the match ipv4 source address key field statement. Cisco IOS Flexible NetFlow will also include nonkey field information about source and destination IPv4 addresses, protocol, ports (if present), ingress and egress interfaces, and packets per flow.

!
!-- Configure key and nonkey fields
!-- in the user-defined flow record
!
flow record FLOW-RECORD-ipv4
 match ipv4 source address
 collect ipv4 protocol
 collect ipv4 destination address
 collect transport source-port
 collect transport destination-port
 collect interface input
 collect interface output
 collect counter packets
!
!-- Configure the flow monitor to
!-- reference the user-defined flow 
!-- record
!
flow monitor FLOW-MONITOR-ipv4
 record FLOW-RECORD-ipv4
!
!-- Apply the flow monitor to the interface
!-- in the ingress direction
!
interface GigabitEthernet0/0
 ip flow monitor FLOW-MONITOR-ipv4 input

The Cisco IOS Flexible NetFlow flow output is as follows:

router#show flow monitor FLOW-MONITOR-ipv4 cache format table
  Cache type:                               Normal
  Cache size:                                 4096
  Current entries:                               6
  High Watermark:                                1

  Flows added:                                   9181
  Flows aged:                                    9175
    - Active timeout      (  1800 secs)          9000
    - Inactive timeout    (    15 secs)           175
    - Event aged                                    0
    - Watermark aged                                0
    - Emergency aged                                0

IPV4 SRC ADDR   ipv4 dst addr   trns src port trns dst port intf input intf output pkts   ip prot
=============== =============== ============= ============= ========== =========== ====== =======
 192.168.60.201  192.168.60.102          1456          1900      Gi0/0       Gi0/1   1128     17
 192.168.11.54   192.168.60.158           123          1900      Gi0/0       Gi0/1   2212     17
 192.168.150.60    10.89.16.226          2567           443      Gi0/0       Gi0/1     13      6
 192.168.13.97    192.168.60.28          3451          1900      Gi0/0       Gi0/1      1     17
 192.168.60.17    192.168.60.97          4231          1900      Gi0/0       Gi0/1    146     17
   10.88.226.1   192.168.202.22          2678           443      Gi0/0       Gi0/1  10567      6
  10.89.16.226   192.168.150.60          3562            80      Gi0/0       Gi0/1  30012      6

To only view the SSDP packets on UDP port 1900, use the show flow monitor FLOW-MONITOR-ipv4 cache format table | include IPV4 DST ADDR |_1900_.*_17_ command to display the related NetFlow records.

For more information about Cisco IOS Flexible NetFlow, refer to Flexible Netflow Configuration Guide, Cisco IOS Release 15.1M&T and Cisco IOS Flexible NetFlow Configuration Guide, Release 12.4T.

Identification: IPv6 Traffic Flow Identification Using Cisco IOS Flexible NetFlow

!
!-- Configure key and nonkey fields
!-- in the user-defined flow record
!
flow record FLOW-RECORD-ipv6
 match ipv6 source address
 collect ipv6 protocol
 collect ipv6 destination address
 collect transport source-port
 collect transport destination-port
 collect interface input
 collect interface output
 collect counter packets
!
!-- Configure the flow monitor to
!-- reference the user-defined flow 
!-- record
!
flow monitor FLOW-MONITOR-ipv6
 record FLOW-RECORD-ipv6
!
!-- Apply the flow monitor to the interface
!-- in the ingress direction
!
interface GigabitEthernet0/0
  ipv6 flow monitor FLOW-MONITOR-ipv6 input

The Cisco IOS Flexible NetFlow flow output is as follows:

router#show flow monitor FLOW-MONITOR-ipv6 cache format table
  Cache type:                               Normal
  Cache size:                                 4096
  Current entries:                               6
  High Watermark:                                2

  Flows added:                                   539
  Flows aged:                                    532
    - Active timeout      (  1800 secs)          350
    - Inactive timeout    (    15 secs)          182
    - Event aged                                   0
    - Watermark aged                               0
    - Emergency aged                               0

IPV6 SRC ADDR     ipv6 dst addr     trns src port trns dst port intf input intf output pkts ip prot
================= ================= ============= ============= ========== =========== ==== =======
2001:DB...06::201  2001:DB...28::20           123           123      Gi0/0       Gi0/0   17      17
2001:DB...128::201  2001:DB...28::20         1265          1900      Gi0/0       Gi0/0 1237      17
2001:DB...128::201  2001:DB...28::20         1441          1900      Gi0/0       Gi0/0 2346      17
2001:DB...06::201  2001:DB...28::20          1890          1900      Gi0/0       Gi0/0 5009      17
2001:DB...06::201  2001:DB...28::20          2856          5060      Gi0/0       Gi0/0  486      17
2001:DB...06::201  2001:DB...28::20          3012            53      Gi0/0       Gi0/0 1016      17
2001:DB...06::201  2001:DB...28::20          2477            53      Gi0/0       Gi0/0 1563      17

To permit display of the full 128-bit IPv6 address, use the terminal width 132 exec mode command.

To view only the SSDP on UDP port 1900, use the show flow monitor FLOW-MONITOR-ipv6 cache format table | include IPV6 DST ADDR|_1900_.*_17_ command to display the related Cisco IOS Flexible NetFlow records.

Cisco ASA, Cisco ASASM, and Cisco FWSM Firewalls

Mitigation: Transit Access Control Lists

To protect the network from traffic that enters the network at ingress access points, which may include Internet connection points, partner and supplier connection points, or VPN connection points, administrators are advised to deploy tACLs to perform policy enforcement. Administrators can construct a tACL by explicitly permitting only authorized traffic to enter the network at ingress access points or permitting authorized traffic to transit the network in accordance with existing security policies and configurations. A tACL workaround cannot provide complete protection against these vulnerabilities when the attack originates from a trusted source address.

The tACL policy denies unauthorized SSDP packets on UDP port 1900 that are sent to affected devices. In the following example, 192.168.60.0/24 and 2001:DB8:1:60::/64 represent the IP address space that is used by the affected devices, and the hosts at 192.168.100.1 and 2001:DB8::100:1 are considered trusted sources that require access to the affected devices. Care should be taken to allow required traffic for routing and administrative access prior to denying all unauthorized traffic.

Additional information about tACLs is in Transit Access Control Lists: Filtering at Your Edge.

!
!-- Include explicit permit statements for trusted sources
!-- that require access on the vulnerable protocol and port
!
access-list tACL-Policy extended permit udp host 192.168.100.1 
     192.168.60.0 255.255.255.0 eq 1900
access-list tACL-Policy extended permit udp host 192.168.100.1 
     host 239.255.255.250 eq 1900
!
!-- The following vulnerability-specific access control entries
!-- (ACEs) can aid in identification of attacks
!
access-list tACL-Policy extended deny udp any 192.168.60.0 255.255.255.0 eq 1900
!
!-- Permit or deny all other Layer 3 and Layer 4 traffic in accordance
!-- with existing security policies and configurations
!
!-- Explicit deny for all other IP traffic
!
access-list tACL-Policy extended deny ip any any
!
!-- Create the corresponding IPv6 tACL
!
!-- Include explicit permit statements for trusted sources
!-- that require access on the vulnerable protocol and port
!
ipv6 access-list IPv6-tACL-Policy permit udp host 2001:DB8::100:1
          2001:db8:1:60::/64 eq 1900
ipv6 access-list IPv6-tACL-Policy permit udp host 2001:DB8::100:1
          host FF02:0:0:0:0:0:0:C eq 1900
ipv6 access-list IPv6-tACL-Policy permit udp host 2001:DB8::100:1
          host FF05:0:0:0:0:0:0:C eq 1900
ipv6 access-list IPv6-tACL-Policy permit udp host 2001:DB8::100:1
          host FF08:0:0:0:0:0:0:C eq 1900
ipv6 access-list IPv6-tACL-Policy permit udp host 2001:DB8::100:1
          host FF0E:0:0:0:0:0:0:C eq 1900
!
!--  The following vulnerability-specific access control entries
!--  (ACEs) can aid in identification of attacks
!
ipv6 access-list IPv6-tACL-Policy deny udp any 2001:db8:1:60::/64 eq 1900
!
!--  Permit or deny all other Layer 3 and Layer 4 traffic in accordance
!--  with existing security policies and configurations
!
!--  Explicit deny for all other IP traffic
!
ipv6 access-list IPv6-tACL-Policy deny ip any any
!
!--  Apply tACLs to interfaces in the ingress direction
!
access-group tACL-Policy in interface outside
access-group IPv6-tACL-Policy in interface outside

Identification: Transit Access Control Lists

After the tACL has been applied to an interface, administrators can use the show access-list command to identify the number of SSDP packets on UDP port 1900 t that have been filtered. Administrators are advised to investigate filtered packets to determine whether they are attempts to exploit these vulnerabilities. Example output for show access-list tACL-Policy and show access-list IPv6-tACL-Policy follows:

firewall#show access-list tACL-Policy
access-list tACL-Policy; 4 elements; name hash: 0x3452703d
access-list tACL-Policy line 1 extended permit udp host 192.168.100.1 
     192.168.60.0 255.255.255.0 eq 1900 (hitcnt=31)
access-list tACL-Policy line 2 extended permit udp host 192.168.100.1 
     host 239.255.255.250 eq 1900 (hitcnt=11) 
access-list tACL-Policy line 3 extended deny udp any 192.168.60.0 
     255.255.255.0 eq 1900 (hitcnt=8)
access-list tACL-Policy line 4 extended deny ip any any (hitcnt=8)

In the preceding example, access list tACL-Policy has dropped 8 SSDP packets on UDP port 1900 received from an untrusted host or network. In addition, syslog message 106023 can provide valuable information, which includes the source and destination IP address, the source and destination port numbers, and the IP protocol for the denied packet.

firewall#show access-list IPv6-tACL-Policy                 
ipv6 access-list IPv6-tACL-Policy; 7 elements; name hash: 0x566a4229
ipv6 access-list IPv6-tACL-Policy line 1 permit udp host 2001:db8:1:100::1 
     2001:db8:1:60::/64 eq 1900 (hitcnt=59) 
ipv6 access-list IPv6-tACL-Policy line 2 permit udp host 2001:db8:1:100::1 
     host FF02:0:0:0:0:0:0:C eq 1900 (hitcnt=14) 
ipv6 access-list IPv6-tACL-Policy line 3 permit udp host 2001:db8:1:100::1 
     host FF05:0:0:0:0:0:0:C eq 1900 (hitcnt=17)
ipv6 access-list IPv6-tACL-Policy line 4 permit udp host 2001:db8:1:100::1 
     host FF08:0:0:0:0:0:0:C eq 1900 (hitcnt=11)
ipv6 access-list IPv6-tACL-Policy line 5 permit udp host 2001:db8:1:100::1 
     host FF0E:0:0:0:0:0:0:C eq 1900 (hitcnt=12)
ipv6 access-list IPv6-tACL-Policy line 6 udp any 
     2001:db8:1:60::/64 eq 1900 (hitcnt=47)
ipv6 access-list IPv6-tACL-Policy line 7 deny ip any any (hitcnt=27)

In the preceding example, access list IPv6-tACL-Policy has dropped 47 SSDP packets on UDP port 1900 received from an untrusted host or network. In addition, syslog message 106023 can provide valuable information, which includes the source and destination IP address, the source and destination port numbers, and the IP protocol for the denied packet.

In addition, syslog message 106023 can provide valuable information, which includes the source and destination IP address, the source and destination port numbers, and the IP protocol for the denied packet.

Identification: Firewall Access List Syslog Messages

Firewall syslog message 106023 will be generated for packets denied by an access control entry (ACE) that does not have the log keyword present. Additional information about this syslog message is in Cisco ASA 5500 Series System Log Message, 8.2 - 106023.

Information about configuring syslog for the Cisco ASA 5500 Series Adaptive Security Appliance is in Monitoring - Configuring Logging. Information about configuring syslog on the Cisco Catalyst 6500 Series ASA Services Module is in Configuring Logging. Information about configuring syslog on the FWSM for Cisco Catalyst 6500 Series Switches and Cisco 7600 Series Routers is in Monitoring the Firewall Services Module.

In the following example, the show logging | grep regex command extracts syslog messages from the logging buffer on the firewall. These messages provide additional information about denied packets that could indicate potential attempts to exploit the vulnerabilities that are described in this document. It is possible to use different regular expressions with the grep keyword to search for specific data in the logged messages.

Additional information about regular expression syntax is in Creating a Regular Expression.

firewall#show logging | grep 106023
  Jan 29 2013 00:15:13: %ASA-4-106023: Deny udp src outside:192.0.2.18/2944 
         dst inside:192.168.60.191/1900 by access-group "tACL-Policy"
  Jan 29 2013 00:15:13: %ASA-4-106023: Deny udp src outside:192.0.2.200/2945 
         dst inside:192.168.60.33/1900 by access-group "tACL-Policy"
firewall#

In the preceding example, the messages logged for the tACL tACL-Policy show potentially spoofed SSDP packets for UDP port 1900 sent to the address block assigned to affected devices.

Additional information about syslog messages for Cisco ASA Series Adaptive Security Appliances is in Cisco ASA 5500 Series System Log Messages, 8.2. Additional information about syslog messages for Cisco Catalyst 6500 Series ASA Services Module is in the Analyzing Syslog Messages section of the Cisco ASASM CLI Configuration Guide. Additional information about syslog messages for the Cisco FWSM is in Catalyst 6500 Series Switch and Cisco 7600 Series Router Firewall Services Module Logging System Log Messages.

For additional information about investigating incidents using syslog events, reference the Identifying Incidents Using Firewall and IOS Router Syslog Events Cisco Security Intelligence Operations white paper.

Mitigation: Spoofing Protection Using Unicast Reverse Path Forwarding

The vulnerabilities that are described in this document can be exploited by spoofed IP packets. Administrators can deploy and configure uRPF as a protection mechanism against spoofing.

uRPF is configured at the interface level and can detect and drop packets that lack a verifiable source IP address. Administrators should not rely on uRPF to provide complete spoofing protection because spoofed packets may enter the network through a uRPF-enabled interface if an appropriate return route to the source IP address exists. In an enterprise environment, uRPF may be enabled at the Internet edge and at the internal access layer on the user-supporting Layer 3 interfaces.

For additional information about the configuration and use of uRPF, reference the Cisco Security Appliance Command Reference for ip verify reverse-path and the Understanding Unicast Reverse Path Forwarding Cisco Security Intelligence Operations white paper.

Identification: Spoofing Protection Using Unicast Reverse Path Forwarding

Firewall syslog message 106021 will be generated for packets denied by uRPF. Additional information about this syslog message is in Cisco ASA 5500 Series System Log Message, 8.2 - 106021.

Information about configuring syslog for the Cisco ASA 5500 Series Adaptive Security Appliance is in Monitoring - Configuring Logging. Information about configuring syslog for the Cisco Catalyst 6500 Series ASA Services Module is in Configuring Logging. Information about configuring syslog on the FWSM for Cisco Catalyst 6500 Series Switches and Cisco 7600 Series Routers is in Monitoring the Firewall Services Module.

In the following example, the show logging | grep regex command extracts syslog messages from the logging buffer on the firewall. These messages provide additional information about denied packets that could indicate potential attempts to exploit the vulnerabilities that are described in this document. It is possible to use different regular expressions with the grep keyword to search for specific data in the logged messages.

Additional information about regular expression syntax is in Creating a Regular Expression.

firewall#show logging | grep 106021
  Jan 29 2013 00:15:13: %ASA-1-106021: Deny UDP reverse path check from
         192.168.60.1 to 192.168.60.100 on interface outside
  Jan 29 2013 00:15:13: %ASA-1-106021: Deny UDP reverse path check from
         192.168.60.1 to 192.168.60.101 on interface outside
  Jan 29 2013 00:15:13: %ASA-1-106021: Deny TCP reverse path check from
         192.168.60.1 to 192.168.60.102 on interface outside

The show asp drop command can also identify the number of packets that the uRPF feature has dropped, as shown in the following example:

firewall#show asp drop frame rpf-violated
  Reverse-path verify failed                          11
firewall#

In the preceding example, uRPF has dropped 11 IP packets received on interfaces with uRPF configured. Absence of output indicates that the uRPF feature on the firewall has not dropped packets.

For additional information about debugging accelerated security path dropped packets or connections, reference the Cisco Security Appliance Command Reference for show asp drop.

Cisco Intrusion Prevention System

Mitigation: Cisco IPS Signature Table

Administrators can use the Cisco IPS appliances and services modules to provide threat detection and help prevent attempts to exploit several of the vulnerabilities described in this document. The following table provides an overview of CVE identifiers and the respective Cisco IPS signatures that will trigger events on potential attempts to exploit these vulnerabilities.

* Fidelity is also referred to as Signature Fidelity Rating (SFR) and is the relative measure of the accuracy of the signature (predefined). The value ranges from 0 through 100 and is set by Cisco Systems, Inc.

Administrators can configure Cisco IPS sensors to perform an event action when an attack is detected. The configured event action performs preventive or deterrent controls to help protect against an attack that is attempting to exploit the vulnerabilities listed in the preceding table.

Exploits that use spoofed IP addresses may cause a configured event action to inadvertently deny traffic from trusted sources.

Cisco IPS sensors are most effective when deployed in inline protection mode combined with the use of an event action. Automatic Threat Prevention for Cisco IPS 7.x and 6.x sensors that are deployed in inline protection mode provides threat prevention against an attack that is attempting to exploit the vulnerabilities that are described in this document. Threat prevention is achieved through a default override that performs an event action for triggered signatures with a riskRatingValue greater than 90.

For additional information about the risk rating and threat rating calculation, reference Risk Rating and Threat Rating: Simplify IPS Policy Management.

Cisco Security Manager

Identification: Cisco Security Manager

Cisco Security Manager, Event Viewer

Beginning in software version 4.0, Cisco Security Manager can collect syslogs from Cisco firewalls and Cisco IPS devices and provides the Event Viewer, which can query for events that are related to the vulnerabilities that are described in this document.

Using the IPS Alert Events predefined view in the Event Viewer, the user can enter the search string 1851/0 in the event filter to return all captured events related to Cisco IPS signature 1851/0.

Using the following filters in the Firewall Denied Events predefined view in the Event Viewer provides all captured Cisco firewall access list deny syslog messages that could indicate potential attempts to exploit the vulnerabilities that are described in this document.

• Use the Destination event filter to filter network objects that contain the IP address space that is used by the affected devices (for example, IPv4 address range 192.168.60.0/24 and IPv6 address range 2001:DB8:1:60::/64)
• Use the Destination Service event filter to filter objects that contain UDP port 1900

An Event Type ID filter can be used with the Firewall Denied Events predefined view in the Event Viewer to filter the syslog IDs shown in the following list to provide all captured Cisco firewall deny syslog messages that could indicate potential attempts to exploit the vulnerabilities that are described in this document:

• ASA-4-106021 (uRPF spoofing)
• ASA-4-106023 (ACL deny)

For more information about Cisco Security Manager Events, refer to the Filtering and Querying Events section of the Cisco Security Manager User Guide.

Cisco Security Manager Report Manager

Beginning in software version 4.1, Cisco Security Manager supports the Report Manager, the Cisco IPS event reporting feature. This feature allows an administrator to define reports based on Cisco IPS events of interest. Reports can be scheduled or users can run ad hoc reports as required.

Using the Report Manager, the user can define an IPS Top Signatures report for Cisco IPS devices of interest based on time-range and signature characteristics. When the Signature ID is set to 1851/0, Cisco Security Manager will generate a comprehensive report that ranks the count of the alerts fired for the signature of interest compared to the total sum of all signature alerts shown in the report.

Also in the Report Manager, the Top Services report can be used with the following configuration to generate a report of events that indicate potential attempts to exploit the vulnerabilities that are described in this document:

• Use the Destination IP network filter to filter network objects that contain the IP address space that is used by the affected devices (for example, IPv4 address range 192.168.60.0/24 and IPv6 address range 2001:DB8:1:60::/64)
• Set an action of Deny on the Criteria settings page

For more information about Cisco Security Manager IPS Event Reporting refer to the Understanding IPS Top Reports section of the Cisco Security Manager User Guide.

Identification: Event Management System Partner Events

Cisco works with industry-leading Security Information and Event Management (SIEM) companies through the Cisco Developer Network. This partnership helps Cisco deliver validated and tested SIEM systems that address business concerns such as long-term log archiving and forensics, heterogeneous event correlation, and advanced compliance reporting. Security Information and Event Management partner products can be leveraged to collect events from Cisco devices and then query the collected events for the incidents created by a Cisco IPS signature or deny syslog messages from firewalls that could indicate potential attempts to exploit the vulnerabilities that are described in this document. The queries can be made by Sig ID and Syslog ID as shown in the following list:

• 1851/0 Portable SDK for UPnP Devices Buffer Overflow Vulnerabilities
• ASA-4-106021 (uRPF spoofing)
• ASA-4-106023 (ACL deny)

For more information about SIEM partners, refer to the Security Management System website.

THIS DOCUMENT IS PROVIDED ON AN "AS IS" BASIS AND DOES NOT IMPLY ANY KIND OF GUARANTEE OR WARRANTY, INCLUDING THE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE. YOUR USE OF THE INFORMATION ON THE DOCUMENT OR MATERIALS LINKED FROM THE DOCUMENT IS AT YOUR OWN RISK. CISCO RESERVES THE RIGHT TO CHANGE OR UPDATE THIS DOCUMENT AT ANY TIME.

Complete information on reporting security vulnerabilities in Cisco products, obtaining assistance with security incidents, and registering to receive security information from Cisco, is available on Cisco''s worldwide website at http://www.cisco.com/en/US/products/products_security_vulnerability_policy.html. This includes instructions for press inquiries regarding Cisco security notices. All Cisco security advisories are available at http://www.cisco.com/go/psirt.

• Cisco Applied Mitigation Bulletins
• Cisco Security Intelligence Operations
• Cisco Security IntelliShield Alert Manager Service
• Cisco IOS NetFlow - Home Page on Cisco.com
• Cisco IOS NetFlow White Papers
• NetFlow Performance Analysis
• Cisco Network Foundation Protection White Papers
• Cisco Network Foundation Protection Presentations
• A Security-Oriented Approach to IP Addressing
• Securing Tool Command Language on Cisco IOS
• Cisco Firewall Products - Home Page on Cisco.com
• Cisco Catalyst 6500 Series ASA Services Module
• Unicast Reverse Path Forwarding Enhancements for the Internet Service Provider
• Cisco Intrusion Prevention System
• Cisco IPS Signature Downloads
• Cisco IPS Signature Search Page
• Cisco Security Manager
• Common Vulnerabilities and Exposures (CVE)